Hide Wires on Brick (Color-Matched Mortar Paint)
To make a wire run blend into brick, conceal it inside a listed surface raceway, then paint the raceway only if its manufacturer allows it. Match the coating to the mortar or nearby brick. Do not bury loose cable in mortar or treat paint as protection. Choose supports, wiring, and installation methods for the wall and circuit.
The small details matter: NEC 2023, for example, requires EMT to be supported within 3 feet of a termination and at intervals no greater than 10 feet. Those figures apply to EMT, not automatically to every raceway. The locally adopted code, product listing, and installation instructions determine what is suitable for your particular route.
I start by identifying the wiring and wall construction, then plan a route that keeps fittings accessible. This guide explains how to choose and install a paintable surface raceway, match its finish to mortar, and check the result without mistaking a neat appearance for a safe installation.
Plan the route and identify the wiring
A surface raceway is a listed channel that holds and protects conductors on a wall. It can make a cable route less noticeable without cutting into brick. Before choosing one, identify the circuit, exposure, wall assembly, and local code rules; the right finish cannot correct an unsuitable wiring method.
Classify the wire and wall
First determine whether the run carries power or low-voltage signals, such as speaker, network, or security wiring. Identify the cable type and whether it is approved for the planned wiring method. If you cannot tell what a cable is, do not assume it can go inside a raceway or share space with power conductors.
Next establish whether the wall is indoors or outdoors and whether the brick is solid masonry or veneer. Brick veneer can have a drainage cavity behind it and is not automatically a safe anchor base. Look for existing boxes and penetrations, and locate concealed services before drilling.
- Check the locally adopted NEC edition and local amendments.
- Confirm whether the route touches a rated wall, historic masonry, or a shared building envelope. Ask the relevant authority or building owner before altering these.
- Plan for access to boxes, fittings, and any junctions; a splice must not become inaccessible behind a finish.
Choose a route that looks intentional
On a brick wall, a straight run aligned with a mortar joint, corner, or trim line often draws less attention than a diagonal path. This is a visual choice, not permission to use mortar as a channel. Keep the cable in a suitable raceway, and avoid cutting a chase into the masonry and covering it with mortar.
A paint-matched raceway can blend with a mortar joint, but the channel may still be visible because its shape and surface differ from mortar. Test a short sample in the actual lighting before coating the full length.
| Route or finish | When it may suit | Main check |
|---|---|---|
| Raceway painted to match mortar | A narrow, straight route near a joint | Confirm the raceway and coating makers allow painting |
| Raceway matched to brick | A route across a brick face | Test color and sheen on a sample |
| Unpainted raceway | Product finish already blends with the wall | Check contrast in daylight and room lighting |
| Cable set into a mortar joint | Not a recommended concealment method | Do not bury ordinary cable or use mortar as a raceway |
Check access, separation, and substrate clearances
A clean route still needs safe spacing, suitable supports, and accessible connections. Check the circuit rules and raceway instructions before drilling or pulling conductors. Brick, mortar, and veneer behave differently under fasteners, so choose anchors for the actual substrate and load, rather than assuming a mortar joint is the best place to drill.
Keep power and low-voltage wiring properly separated
NEC 2023 Section 725.136 restricts Class 2 and Class 3 circuits from sharing an enclosure or raceway with power conductors unless a listed exception or an allowed barrier or insulation arrangement applies. The right answer depends on the circuit classification and installation details. Do not put speaker or network cable in a power raceway just because it fits.
If you are unsure of the circuit class, raceway rules, or applicable exception, ask a qualified electrician or low-voltage professional familiar with local requirements. Plan separate routes where needed, and keep boxes and terminations accessible.
For an exterior route, raceway interiors may be treated as wet locations under NEC 300.9. Conductors used there must be identified for wet locations under 310.10(C). A weather-resistant cover or exterior paint does not make an indoor-only conductor suitable for a wet location.
Choose anchors for the actual brick assembly
Brick veneer is not automatically a structural anchor surface. Drilling or loading it can crack the brick or affect the drainage space behind it. Do not assume a mortar joint is safe for fasteners; identify the wall assembly and use a fastening method rated for the substrate and expected load.
The 1¼-inch (32 mm) clearance in NEC 300.4(A)(1) is a wood-framing protection rule. It applies when a cable or raceway passes through or alongside wood framing: keep the nearest edge of the hole or notch at least that far from the framing edge, or use a qualifying steel plate at least 1⁄16 inch (1.6 mm) thick. It is not a general clearance rule for brick.
Install listed raceway and apply the color-matched finish
The raceway, fittings, boxes, conductors, and coating work as a system. Follow the product listing and installation instructions, and do not substitute paint or mortar for a required part. For power wiring, use a qualified electrician when required by local rules or when you are not equipped to verify the circuit and installation.
Mount the raceway and check its capacity
De-energize applicable power circuits before work. Use raceway and fittings listed for the intended use, and install them with supports and anchors suited to the wall. Maintain required conductor separation, follow bend limits, and keep junctions accessible. Never use mortar as a raceway or junction enclosure.
If EMT is selected, NEC 2023 Section 358.30 requires support within 3 feet (900 mm) of each box, cabinet, conduit body, or other termination, and at intervals no greater than 10 feet (3 m). Check the local code and the support and fitting manufacturers’ instructions. These spacing figures are EMT-specific; other raceways may have different requirements.
Do not estimate raceway capacity by eye. NEC 2023 Chapter 9, Table 1 generally limits conduit fill to 40% when it contains more than two conductors. Calculate fill using the applicable code tables and the conductors’ insulation dimensions. Check bonding and grounding requirements as well. Pull conductors only after confirming fill, bends, and access.
Paint the raceway without hiding required features
Check the raceway manufacturer’s instructions before painting. Some products permit paint; others may restrict coating or require a specific preparation. Use a compatible coating and test the color on a short sample. Mortar varies in color and texture, so a sample viewed at the same distance and under the same light is more useful than a paint chip alone.
- Clean and prepare the surface only as the product instructions allow.
- Apply a thin, even coat; heavy paint can affect fit or cover details.
- Keep labels, openings, fittings, and access covers clear unless the manufacturer specifically permits coating them.
- Do not paint over loose cable jackets or use paint to fill gaps or protect damaged wiring.
Matching the wall color may reduce contrast, but it will not make the raceway physically disappear. A route aligned with a mortar joint and finished in a similar tone often looks less prominent than a route that cuts across the brick face.
Verify support, access, and electrical compliance
A final check should confirm both the visual finish and the installation beneath it. Look for secure supports, accessible boxes and covers, compatible materials, and conductors suited to the location. If any part of the route is uncertain, stop before painting and ask a qualified installer or the local authority having jurisdiction.
Two practical layout examples
These are planning examples, not claims about a specific completed installation. They show how the wall and wiring type change the choices.
Indoor TV on a brick veneer wall: A homeowner wants a power route and a low-voltage HDMI or network route to look discreet. I would first identify the veneer assembly and locate concealed services, then plan separate raceways unless the applicable rules allow another arrangement. I would confirm an anchor method suited to the veneer and paint only products whose instructions permit it.
Exterior camera on a masonry wall: The cable route is exposed to weather. I would confirm the raceway and fittings are suitable for the environment, and verify that conductors inside a raceway treated as a wet location are identified for that use. A coat of exterior paint alone does not establish weather suitability.
Inspect before and after painting
Before coating, verify that the route is firmly supported, the raceway is not overfilled, and all required junctions and access covers remain reachable. Check that fittings are correctly seated and that the wiring method matches the circuit and location. For power work, have a qualified person verify operation and code compliance where required.
After painting, inspect the full route in daylight and at night. Make sure no opening, label, fitting, or cover has been obscured. Keep the paint and product details for future repairs, and do not seal a cover that must remain accessible.
Frequently asked questions
These answers focus on the key choice: how to make a brick-wall cable route less visible without burying a cable or defeating the raceway’s safety and access requirements. The product listing, installation instructions, and locally adopted code still govern the final installation.
Can I paint a surface raceway to match mortar?
Only if the raceway manufacturer permits painting and the coating is compatible. Test a small sample, then keep labels, openings, fittings, and access covers visible unless the instructions specifically allow coating them.
Can I put a wire directly in a mortar joint?
Do not bury ordinary cable in mortar or treat the joint as a raceway. Use a suitable listed raceway or another wiring method approved for that circuit, location, and wall assembly.
Is paint enough to protect a cable on brick?
No. Paint is a finish, not electrical insulation or physical protection. Use a wiring method suited to the circuit and location, and do not paint over a loose cable as a substitute for a raceway.
Can power and speaker wires share one raceway?
Not by default. NEC 2023 Section 725.136 limits sharing enclosures or raceways between Class 2 or Class 3 circuits and power conductors, subject to specific exceptions. Verify the circuit classification and the exact exception before combining them.
How often does EMT need support?
Under NEC 2023 Section 358.30, EMT must be fastened within 3 feet of each termination and supported at intervals no greater than 10 feet. Check local amendments and manufacturer instructions; other raceway types may have different rules.
Can I anchor the raceway into brick veneer?
Do not assume the veneer is a suitable structural anchor. Identify the wall assembly and use a fastening method rated for the substrate and load. Drilling or loading veneer can crack it or affect the drainage cavity.
Does an exterior raceway make indoor wire safe outside?
No. Where the raceway interior is treated as a wet location, NEC 300.9 and 310.10(C) require conductors identified for that use. An exterior-rated raceway does not make unsuitable conductors acceptable.
Can I cover a junction box with paint or mortar?
No. Keep junctions and access covers accessible, and do not conceal a splice behind mortar or a finished surface. Paint only as the product instructions allow, without blocking required access or openings.
How do I calculate raceway fill?
Use the applicable NEC Chapter 9 tables and the conductor insulation dimensions, rather than estimating by sight. Chapter 9, Table 1 generally sets a 40% fill limit for conduit with more than two conductors; check the specific wiring method and conditions.
Should I cut a channel into the brick instead?
Do not cut a chase and patch over it as a shortcut for hiding cable. It can damage masonry and does not by itself create an approved wiring method. Use an appropriate listed surface system or consult a qualified professional.
A paint-matched raceway can make a brick-wall cable run far less conspicuous, but the order matters: identify the circuit and wall, select a suitable listed system, install and support it correctly, then apply a compatible finish. Keep every required connection accessible, and let the adopted code and product instructions guide the details.
(This article was written by one of our staff writers, Michael Holloway. Visit our Meet the Team page.)






