Hide Living Room Side Table Wires (Hollow Leg)
To hide a side-table cord inside a hollow leg, route one intact, approved cord through a smooth, protected opening while keeping its plug and every connection outside the leg and accessible. Check the table’s structure first, size the opening to the cord, and never force, cut, or splice the cord to make it fit.
Could you clear the visible wire without turning a simple furniture update into a safety problem? A hollow table leg can conceal a cord neatly, but the route needs planning. The key is to treat the leg as furniture, not as a place to install building wiring. I check the cord, the table, and how the cord will be removed before drilling.
Planning — Intent, Scope & Governing Principles
This approach is for routing an intact appliance cord through a hollow side-table leg. The plug and any adapters or power supplies stay outside the leg, where you can reach and inspect them. Follow the appliance instructions and local rules; a furniture-leg route is not a substitute for fixed wiring.
NEC 2023 section 400.12 restricts certain uses of flexible cords, including routing them through building walls, ceilings, or floors and concealing them behind building finishes. That rule does not, by itself, provide a complete design for routing a cord through furniture. Keep the route within the table, and do not continue it into a wall, floor, or ceiling.
Confirm the cord and table
Start by identifying the cord and the equipment it powers. Check the appliance instructions for cord requirements, and look for damage such as cuts, flattened areas, or loose connections. Do not use a damaged cord for a concealed furniture route.
Then inspect the leg. Look for seams, screws, brackets, joints, drawer slides, and other hardware that may be hidden inside or near the proposed path. A hollow appearance does not prove the leg is safe to drill. Some legs support the table through a narrow wall or a reinforced joint.
Decide how the cord will enter
Plan how the cord will go into and out of the leg before making an opening. If the plug cannot pass through the planned route, do not force it through or remove a molded plug. You may be able to feed the intact cord through an open leg end before assembly, if the table design allows it. Otherwise, use a detachable cord system only if the equipment maker permits it.
Access & Clearances — Verified Design Criteria
A workable route gives the cord enough room, protects it from sharp edges, and leaves the plug and connections reachable. Measure the cord itself and account for bends, hardware, and the method of feeding it through the leg. The dimensions below are project fit criteria, not universal electrical code limits.
Size the opening and protect its edge
Measure the cord’s outside diameter at the thickest point that will pass through the opening. As a practical fit target, make the finished opening 2–4 mm wider than that measurement. This is not a code minimum. Check the actual cord and the planned installation method; do not enlarge a structural leg without first assessing it.
Fit a smooth grommet that is held securely in the opening and suits both the hole and the cord. A grommet lines the edge so the cord does not rub against raw material. Deburr the hole first, and check for exposed screws or other sharp edges that could touch the cord.
| Check | Practical criterion | Why it matters |
|---|---|---|
| Finished opening | Cord outside diameter plus 2–4 mm | Allows a suitable fit without squeezing the cord |
| Grommet | Smooth, mechanically retained, sized to the opening and cord | Protects the cord from abrasion |
| Plug and connections | Outside the leg and accessible | Keeps connections available for inspection and service |
| Bend and route | At least the cord maker’s minimum bend radius; clear of moving parts | Reduces stress, pinching, and wear |
| Leg structure | Confirm wall thickness and avoid joints before drilling | Prevents an unassessed change to a load-bearing part |
Allow for bends, movement, and access
A cord’s minimum bend radius is the tightest bend its maker allows. Check the cord documentation when available; there is no single NEC bend-radius value for an ordinary appliance cord. Keep the cord clear of drawer slides, hinges, sharp internal corners, and any moving parts.
Leave enough accessible slack at each end to avoid pulling on the appliance connection. Secure the cord against movement without crushing it. Keep plugs, splices, adapters, power strips, and transformers out of the hollow leg. Enclosing equipment can limit access and may trap heat.
Execution — Survey, Route & Finish
Work through the route in order: inspect, plan, cut, protect, feed, and check. Do not drill until you understand the leg’s construction and have a workable way to install and remove the intact cord. If any step would require damaging the cord or weakening an unassessed part, stop and choose another route.
1. Survey the route
Measure the cord diameter and inspect the leg for material, wall thickness, fasteners, joints, and moving hardware. Identify where the cord enters and exits. Check that both openings can be reached and that the cord can be fed without pulling hard on the plug or appliance connection.
If you cannot inspect the inside well enough to rule out hardware or a structural joint, do not assume the path is clear. Consider a non-drilling cord-management option instead.
2. Mark, drill, and fit the grommet
Mark the opening only after confirming its position will not compromise a joint or support point. Drill carefully, then remove burrs and debris. Fit the correctly sized, mechanically retained grommet, and check that it sits firmly with no sharp edges or exposed fasteners touching the cord.
Before routing the cord, test the opening with a suitable smooth object of similar size. The cord should not need to be forced through. If it catches, adjust the opening or grommet before installing the cord.
3. Feed and secure the cord
Feed the intact cord through the prepared path using the planned entry method. Keep the plug and all connections outside the leg. Do not strip, splice, or replace a molded plug just to make the cord fit, and do not pull on the cord to drag a plug through a small opening.
Leave accessible slack at both ends. Secure the cord so ordinary table movement will not make it rub or pinch, but do not crush it with a tight tie or clamp. Reassemble the table as intended, then check that it sits firmly and the cord is not trapped.
Installation scenarios
These examples show how the same checks apply to different tables. They are planning scenarios, not claims about a particular table or a universal approval to drill. The table maker’s instructions and the actual construction determine whether a route is suitable.
| Scenario | What to check | Safer next step |
|---|---|---|
| Hollow metal leg with an accessible open end | Whether the cord can be fed from the open end and whether the planned route avoids sharp internal edges | Use a protected opening, and keep the plug outside |
| Hollow wood leg with a visible joint nearby | Whether drilling could weaken the joint or reduce the leg’s wall thickness | Do not drill until the structure is assessed; use an external cord cover if uncertain |
| Plug is wider than the leg opening | Whether the cord can be fed from an open end before the table is assembled | Do not force the plug or alter a molded cord; choose a permitted detachable system or another route |
Verification — Edge Cases & Exclusions
After installation, confirm that the cord remains undamaged, accessible at both ends, and clear of moving parts. A neat appearance is not enough: the route must also allow inspection and removal. If you cannot verify those conditions, undo the route and use a different furniture-level solution.
Check the finished route
With the table assembled, inspect both ends of the cord and the grommets. Confirm the cord slides without scraping, is not pinched, and has no tight bend. Make sure the table is stable and the cord does not pull when the table or connected equipment is moved in normal use.
If the cord shifts against the opening, becomes trapped, or shows wear, stop using that route until you correct the cause. Do not hide a damaged section inside the leg.
Know when not to proceed
A hole in furniture does not authorize routing a flexible cord through a building wall, floor, or ceiling. NEC 2023 section 400.12 restricts specified uses of flexible cords in those building locations and behind building finishes. Local adoption and the exact installation matter, so check applicable rules before any route leaves the furniture.
Do not drill an unassessed load-bearing leg, pass a cord through an unprotected hole, or place a power strip or transformer inside the cavity. There is no generic safe hole size or load rating for an unspecified table leg. If the structure is unclear, choose a surface-mounted cord cover or ask a qualified professional to assess the table.
Frequently Asked Questions
These answers cover the common decisions that come up when routing a side-table cord through a hollow leg. The same limits apply throughout: protect the cord, keep connections accessible, and do not treat furniture as a pathway for building wiring.
Can I put a power strip inside the hollow leg?
No. Keep power strips, adapters, plugs, and transformers outside the leg and accessible. A narrow cavity can limit access and may trap heat.
How large should the hole be?
As a project fit target, make the finished opening 2–4 mm wider than the cord’s measured outside diameter. Confirm the grommet and actual cord fit without force. This is not a code minimum.
Can I cut off the plug and reconnect it after threading the cord?
No. Do not cut or splice a molded mains cord to get it through the leg. Use an installation method allowed by the equipment maker, or choose another route.
Can the plug pass through the cord opening?
Only if the planned opening and route allow it without force or damage. Often the cord must be fed from an accessible open end. Never squeeze a plug through an undersized hole.
Do I need a grommet?
Use a smooth, securely retained grommet sized to the finished opening and cord. It protects the cord from contact with a sharp or rough edge.
Can I drill any hollow table leg?
No. A hollow leg may still contain hardware or support a structural joint. Check its construction and remaining wall thickness first; if you cannot assess them, do not drill.
Can the cord continue from the leg into a wall?
Do not use the furniture route to carry a flexible cord into a wall, floor, or ceiling. Building wiring rules apply to those locations, and NEC 2023 section 400.12 restricts specified flexible-cord uses there.
What if the cord is pinched or scuffed after installation?
Stop using the route and inspect the cord. Replace a damaged cord as directed by the equipment maker; do not conceal damage inside the leg.
(This article was written by one of our staff writers, Michael Holloway. Visit our Meet the Team page.)




