What Is Polymer Permeation Resistance? (ASTM Standards)
Polymer permeation resistance describes how well a specific polymer slows a named gas, vapor, or chemical under stated test conditions. ASTM methods measure particular kinds of transmission; they do not set one universal pass/fail limit. Choose a method for the permeant and use, test representative material, then compare the result with a documented project acceptance criterion.
Imagine choosing a polymer liner because it stayed intact during a quick chemical splash test. Would it still protect the contents after days of contact, at a higher temperature, or through a thinner section? Appearance alone cannot answer that. Permeation can occur without visible damage, so a sound specification needs test data that matches the intended exposure.
What polymer permeation resistance measures
Polymer permeation resistance is a material’s ability to slow the movement of a substance through it. The result applies to a named permeant and stated conditions, not to a polymer family in general. A test may characterize gas, water vapor, or chemical transmission, but those results answer different questions.
Three quantities are often confused:
- Transmission rate is the amount passing through a specimen per area per time, such as grams per square metre per day (g/m²·day).
- Permeability is a normalized material property, where the method and data allow adjustment for specimen thickness and the driving force. Its units depend on the substance and calculation.
- Breakthrough time is the elapsed time before a method-defined amount is detected on the receiving side. It is not the same as the steady-state permeation rate, which describes transmission after the rate stabilizes.
A low transmission rate under one test does not establish chemical protection in another use. Results depend on polymer formulation, specimen thickness, permeant, temperature, concentration or pressure difference, conditioning, and exposure time. Treat each result as a bounded measurement, not a universal rating.
Define the permeant, exposure, and acceptance criterion
A useful test begins with the service conditions. Record what may contact the polymer, for how long, at what concentration and temperature, and whether contact is continuous, intermittent, or only on one side. Then state the maximum transmission or minimum breakthrough performance that the project will accept.
I would not specify “chemical resistant” as the only requirement. Identify each chemical in a mixture where possible, along with its concentration and likely temperature range. Note whether the material is a film, a molded part, a coating, a seam, or protective clothing. Each may need different specimen preparation or test methods.
Set the acceptance limit before testing. ASTM methods describe procedures; they do not provide one threshold that makes every polymer “permeation-resistant.” The limit should reflect exposure duration, the consequence of failure, and any relevant workplace or regulatory requirements. If the application has no established limit, have the responsible technical or safety professional set one.
Select the ASTM method that matches the question
An ASTM number identifies a test method, not a general approval. Select the method for the permeant and end use, and confirm the current edition and apparatus requirements with ASTM and the testing laboratory. A result for oxygen or water vapor cannot be used as a substitute for a solvent-permeation test.
| ASTM method | What it measures | Appropriate use and limit |
|---|---|---|
| D1434 | Gas transmission through plastic film and sheeting using the method’s specified apparatus and conditions | Gas-transmission characterization. It does not certify liquid-chemical resistance or protective-clothing suitability. |
| D3985 | Oxygen transmission through plastic film and sheeting using a coulometric sensor | Oxygen-barrier characterization. It is not a test for other gases or chemicals. |
| F1249 | Water-vapor transmission through plastic film and sheeting using a modulated infrared sensor | Water-vapor barrier characterization, not a general chemical-permeation rating. |
| E96/E96M | Water-vapor transmission of materials using specified procedures | Select and report the applicable procedure and conditions. Do not assume results are interchangeable with F1249. |
| F739 | Chemical permeation through protective-clothing materials under continuous chemical contact | Protective-clothing material evaluation. Report the chemical, specimen, exposure conditions, breakthrough result, and required permeation-rate data for the applicable edition. |
A laboratory may advise that another method better fits a particular product or application. Do not choose a method just because it produces a familiar unit or a convenient comparison. First define what must be measured.
Confirm specimen geometry, thickness, and test conditions
The test specimen should represent the installed material as closely as practical. State the actual formulation and thickness, including coatings or layers that form part of the barrier. If seams, joints, or processing changes could affect performance, ask whether they need separate evaluation; a flat-film result does not automatically characterize an assembly.
Before testing, agree with the laboratory on exposed area, conditioning, temperature, chemical identity and concentration, contact mode, pressure or concentration driving force, and test duration. These details help make the result interpretable and repeatable. Ask the laboratory to identify the method edition, any deviations, and detection limits.
Thickness matters, but a result cannot always be scaled by thickness alone. Permeability calculations require the relevant driving force and assumptions, and those may not hold across different formulations, temperatures, or exposure conditions. For chemical mixtures in particular, do not assume that a result for one component predicts the behavior of the mixture.
Read permeation data without overclaiming
A test report is useful only when its conditions travel with the number. Review the measured quantity, units, specimen thickness, exposed area, temperature, chemical concentration, conditioning, duration, and method edition. Check whether the reported rate is an observed transmission rate or a normalized value.
For example, an oxygen transmission rate in cubic centimetres per square metre per day describes oxygen transmission under the reported conditions. It does not establish resistance to a cleaning solvent. Similarly, a water-vapor transmission rate in g/m²·day is not a chemical-permeation rating. Units may look comparable while the substances and test principles differ.
Compare the result with the project limit set in advance. Account for the report’s detection limits and uncertainty; “not detected” means below the method’s stated detection capability, not necessarily zero transmission. If a reported breakthrough time exceeds the test duration, describe it as exceeding that duration under those test conditions, rather than assigning an unlimited service life.
Practical examples: matching tests to material use
These are illustrative specification scenarios, not reports of named projects. They show how the test choice follows the exposure and the decision the designer needs to make. Actual method details and limits must be confirmed for the product and application.
| Scenario | Test question | Suitable direction | What not to conclude |
|---|---|---|---|
| A plastic film used to limit oxygen entry into packaged contents | How much oxygen passes through the film under defined conditions? | Consider D3985; report thickness and test conditions. | Do not infer resistance to solvents or other gases. |
| A membrane used to control moisture movement | What is its water-vapor transmission under the specified procedure? | Consider F1249 or the applicable E96/E96M procedure. | Do not treat the two methods’ values as automatically interchangeable. |
| Protective clothing exposed continuously to a named chemical | When does breakthrough occur, and what permeation rate is measured? | Consider F739 for representative clothing material and exposure conditions. | Do not assume the result applies to a different chemical, mixture, garment seam, or service temperature. |
| A component exposed to a process gas | What gas transmission occurs through the specified plastic specimen? | Consider D1434 if the material and test arrangement fit the method. | Do not treat the result as proof of liquid-chemical protection. |
In each example, the practical decision is not simply “Which polymer is best?” It is whether a specified product, at its actual thickness and under the defined exposure, meets the project’s acceptance criterion.
Test, compare, and control changes
Use a documented sequence so the test can support a defensible material choice. The key is to keep the exposure definition, specimen, method, and acceptance decision linked in one record.
- Define exposure. List each gas, chemical, or mixture; its concentration; contact mode; temperature range; and expected duration. State the required limit and why it is suitable for the use.
- Select the method. Match the permeant and end use to an ASTM procedure. Confirm the current edition and laboratory capability.
- Test representative material. Specify formulation, thickness, relevant coating or construction details, conditioning, and test conditions. Use a qualified laboratory and request method deviations and detection limits.
- Compare and document. Compare the measured value with the pre-established criterion, considering uncertainty and test limits. Keep the complete report, not just a summary number.
- Reassess changes. Re-test when formulation, thickness, processing, joints, or service conditions change in a way that could affect barrier performance.
A material can look unchanged while a chemical passes through it. Conversely, an observed change does not by itself quantify transmission. Use the test result, not appearance alone, to judge the barrier.
Conclusion
Polymer permeation resistance is a measured performance under defined conditions, not a blanket property or ASTM certification. Choose a method that matches the permeant and use, test representative material, and compare the data with a project-specific limit. Keep the conditions attached to every result, and do not transfer ratings across chemicals or test types without supporting evidence.
Frequently asked questions
What does polymer permeation resistance mean?
It describes how well a polymer slows a named gas, vapor, or chemical from passing through it under stated test conditions. It is not a universal rating for all exposures.
Does ASTM set a pass/fail limit for permeation resistance?
No single ASTM limit applies to every polymer and use. ASTM methods specify how to measure performance; the project must set its acceptance criterion based on exposure and applicable requirements.
Is permeability the same as transmission rate?
No. Transmission rate reports an amount passing through an area over time. Permeability is normalized for thickness and driving force when the method and data support that calculation.
What does breakthrough time tell me?
It reports when a method-defined amount is detected on the receiving side under the test conditions. It does not, by itself, state the steady-state rate or guarantee a safe service duration.
Can an oxygen transmission result prove solvent resistance?
No. D3985 measures oxygen transmission through plastic film and sheeting. It does not establish resistance to a solvent or other chemical.
Are ASTM F1249 and ASTM E96/E96M results interchangeable?
Not automatically. Both address water-vapor transmission, but they use specified procedures that may differ. Report the method and conditions, and compare results only when the basis is suitable.
Does a test result apply to a different chemical mixture?
Not without validated supporting data. A mixture, concentration, temperature, or contact condition can change performance, so test conditions should match the intended exposure as closely as practical.
What information should a permeation test report include?
At minimum, identify the method and edition, specimen material and thickness, exposed area, permeant and concentration, temperature, conditioning, test duration, measured quantity and units, and relevant detection limits or deviations.
Does “no visible damage” mean the polymer is a good barrier?
No. A hazardous chemical can permeate through material that still looks intact. Appearance is not a substitute for a method-specific transmission or permeation test.
When should a polymer be retested?
Reassess after changes to formulation, thickness, processing, seams or joints, or service conditions that could affect barrier performance. Confirm the need and scope with the responsible technical professional.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)






