Hide Wood Curtain Pole with Cornice (Pelmet Box)
A wooden curtain pole can disappear behind a simple pelmet box if you size the cover around the whole curtain setup, not just the pole. Measure the brackets, rings, finials, and curtain folds, then allow room for movement and removal. Secure the box to suitable backing, keep vents and heat paths clear, and test everything before finishing.
A curtain pole can look like a small detail, yet its brackets and finials may interrupt an otherwise calm window wall. A timber pelmet, also called a cornice box, can hide that hardware and give the window a neat edge. The key is to make the cover look built in without making the curtains harder to use.
I start by treating the pole, curtains, and box as one working assembly. That avoids the common mistake of building a slim cover that fits the pole but catches the rings or traps the curtain folds. The dimensions below are design guidance, not universal code requirements. Check the products and local rules that apply to your home.
Planning: Measure the Pole, Curtains, and Room Constraints
A pelmet is a decorative, non-load-bearing cover fitted over a curtain pole and its hardware. Its size depends on the full space needed by the pole, brackets, rings, finials, and gathered curtains. There is no single code dimension for its depth or height, so measure the actual installation before setting out the box.
Measure the full curtain assembly
Measure the pole from end to end, then note how far the brackets, finials, and curtain rings project from the wall. Also check the curtains when open and closed. A thick curtain may form a deeper stack at one end than it does when hanging flat.
Do not size the box from the pole alone. The widest point may be a bracket arm, a finial, or the folded curtain. If the curtains return toward the wall at either end, include that space too.
For the inside width, start with the widest projection of the pole assembly, then add at least 25 mm (1 in.) of clearance at each end. Add more if the finials, bracket arms, or curtain returns need it. This is practical design guidance, not a code minimum.
Check the room before choosing the shape
Look above and beside the window for framing, wiring, pipes, vents, lights, detectors, and sprinklers. Check that the window opens as intended and that the curtain fabric will not cover a handle or catch on a latch.
A shallow box may suit a close-fitting pole, while a deeper box may be needed for large brackets or heavy curtain folds. A taller front can hide more hardware, but it may also make a small window feel crowded. Mock up the proposed front edge with cardboard or scrap material before you cut timber.
Access and Clearances: Allow for Movement, Removal, and Airflow
The box should conceal the pole without trapping the hardware inside. Clearance means the open space between moving parts and the inside face of the cover. Leave at least 25 mm (1 in.) between the moving curtain hardware and the box as a practical starting point, then test the real setup through its full travel.
Allow space for movement and maintenance
The 25 mm allowance is a design guide, not a guarantee that every curtain will move freely. Rings may swing, fabric may billow, and brackets can need room for fitting or adjustment. Use a full-size mock-up to check the box depth and height before final assembly.
Plan how you will reach the pole later. A fixed, sealed front can make cleaning, changing curtains, or removing a damaged pole difficult. Depending on the design, use a removable front panel, a hinged panel, or an accessible bottom section. Make sure the panel stays secure in normal use and can be opened without damaging the finish.
Check that the pole can be installed and removed through the opening you plan to leave. If the finials must come off first, make sure they can be reached. A cover that hides the pole but prevents routine access is not a useful solution.
Protect airflow and heat clearance
There is no general airflow rate that applies to every pelmet. Do not cover or narrow a supply or return grille, radiator opening, convector opening, or other designed air path. Follow the heating or ventilation equipment maker’s required clearances.
A pelmet above a radiator or close to a grille can affect heat flow even when the curtains move freely. If the equipment’s clearance instructions cannot be met, change the box layout or move it away. Do not assume a decorative cover is harmless simply because it is not sealed.
Execution: Support, Build, and Finish the Pelmet
A pelmet needs a firm support, but it does not carry the curtain pole unless the design specifically makes it part of a rated support system. Fix the pole brackets and box supports into framing, masonry, or suitable backing. Do not rely on unsupported plasterboard alone for a loaded pole or box.
Find suitable fixing points
Locate the wall or ceiling framing and mark its position before drilling. For masonry or other substrates, choose fixings made for that material. Follow the pole and support maker’s instructions for fastener type, embedment, and load limits.
The curtain pole and the pelmet may need separate support points. Do not assume the pelmet cleat can safely carry the pole, or that pole brackets can carry the box. If a suitable fixing point is not available, add properly designed backing or ask a qualified installer to assess the wall.
Build a square, removable cover
A basic timber pelmet often uses a top board, a front face, and short returns at the ends. The exact build depends on the window and the fixing method. Keep the box square and rigid, and check that its inside dimensions match the measured curtain envelope.
Before fixing the cover in place:
- Fit the pole and brackets, or mark their final positions.
- Check that screws will not hit services hidden in the wall or ceiling.
- Dry-fit the pelmet and move the curtains across their full travel.
- Confirm that the front hides the hardware from the main viewing angles.
- Check that any access panel can be removed without scraping the wall or fabric.
Finish the timber before installation where that makes edges easier to reach. Fill and sand visible joints, then paint or stain to suit the room. A painted pelmet that matches the wall can recede visually; a contrasting finish can make it a deliberate trim feature.
Worked Examples: Choose the Box from the Hardware
These examples show how to use measurements, not fixed sizes for every window. The sample dimensions are illustrative. Your pole, brackets, curtain folds, and room conditions may call for a different box.
| Window setup | What to measure first | Design response |
|---|---|---|
| Pole with small rings and compact brackets | Bracket projection and ring movement | Trial a shallow box, keeping at least 25 mm (1 in.) from moving hardware |
| Pole with large finials | Widest end projection and removal path | Extend the inside width beyond the finials, with extra room for fitting |
| Thick curtains that gather at one side | Depth and width of the gathered stack | Increase the box envelope where the fabric bunches |
| Pelmet near a radiator or grille | Equipment clearances and air path | Keep the opening clear or redesign the pelmet location |
Sample width calculation
Suppose a measured pole assembly projects 1,800 mm from its outermost point to the other end, including the finials. Add 25 mm at each end as the minimum practical end clearance. The inside width would start at 1,850 mm. Increase it if the curtain returns or bracket arms need more room.
This calculation does not set the box depth or height. Those depend on the assembly’s projection from the wall, the curtain stack, and the position of the brackets. Measure those dimensions directly rather than applying a standard box size.
A compact window with decorative finials
In a typical design situation, a narrow window has a pole that fits within the window width, but its finials extend beyond the brackets. A box sized only to the bracket span would leave the finials exposed or make them hard to remove. I would first mark the full finial-to-finial span, then add end clearance and test a cardboard face for visual balance.
A deep curtain stack beside a heat source
For a thicker pair of curtains, the open stack can project farther than the pole. If the box is made only to cover the pole, the fabric may rub against its inside face. I would mock up the curtains in their open position and confirm the pelmet does not block a radiator opening or required equipment clearance. If both needs cannot be met, I would revise the location or use a different treatment.
Verification: Test Operation and Check for Obstructions
A finished pelmet should hide the pole while allowing the curtains and window to work as intended. Verification means checking the whole installation in use, not just looking at the closed box. Test movement, access, fixings, and nearby room equipment before you call the work complete.
Run a practical final check
Move the curtains from fully open to fully closed several times. Watch for rings, fabric, or bracket arms touching the box. Open and close the window, and check that handles and latches remain clear.
Then confirm that the pole can still be reached through its planned access panel or opening. Check the box for loose movement and make sure the supports are secure. Finally, confirm that no vent, heat outlet, detector, sprinkler, or other life-safety device has been covered or obstructed.
If you hear rubbing, see the fabric snag, or cannot reach a fixing, do not rely on a quick adjustment after the finish is complete. Remove or revise the cover, correct the clearance, and test again.
FAQ: Wooden Curtain Pole Pelmets
These answers cover common sizing and installation questions. Because pole shapes, curtains, substrates, and room equipment vary, use the actual product instructions and site measurements when they differ from general guidance.
How much clearance should I leave inside a pelmet?
Use at least 25 mm (1 in.) between moving curtain hardware and the box as practical design guidance. Test the full curtain movement, since fabric, rings, and brackets may need more room.
How deep should a curtain pelmet be?
There is no universal depth. Measure the pole, bracket projection, rings, and curtain stack, then allow clearance for movement and access.
How wide should the box be?
Start with the widest projection of the full pole assembly and add at least 25 mm (1 in.) at each end. Add more for returns, bracket arms, or finials that need extra space.
Can I fix a pelmet to plasterboard?
Do not fix a loaded pole or pelmet only to unsupported plasterboard. Use framing, masonry, or properly designed backing, with fixings suited to the substrate and product instructions.
Should the pelmet be removable?
It is wise to plan access for cleaning, curtain changes, and pole repairs. A removable or hinged panel can help, provided it stays secure during normal use.
Can a pelmet go above a radiator?
Only if it preserves the radiator maker’s required clearances and does not disrupt the designed heat path. If the instructions cannot be met, redesign or relocate the pelmet.
Can a pelmet cover a heating or ventilation grille?
No. Do not cover or narrow a supply grille, return grille, radiator opening, or convector opening. Follow the equipment maker’s clearance and airflow requirements.
Is a pelmet box covered by a standard code size?
No universal code minimum sets pelmet depth, height, pole clearance, or airflow. Check adopted local rules and the instructions for the products and equipment involved.
Conclusion: Make the Concealment Work
A well-planned timber pelmet hides the pole without hiding problems. Measure the complete curtain assembly, allow room for movement, provide sound support, and plan access before choosing the final shape. Then test the window, curtains, airflow, and nearby equipment before finishing the installation.
(This article was written by one of our staff writers, Michael Donovan. Visit our Meet the Team page.)






