What Is In-Wall Utility Concealment? (Drywall Chases)
An in-wall utility concealment, or drywall chase, is a framed cavity that hides and routes approved wires, pipes, or ducts behind a finished wall. It must preserve framing strength, required fireblocking, equipment clearances, and access to service parts. Plan the route under locally adopted codes and product instructions before cutting or covering anything.
A chase can make a room look cleaner and protect utilities from accidental damage. But a neat finish is not enough: the space behind drywall still has to meet building and electrical rules. The right design depends on what the chase carries, the wall’s role, and whether workers will need future access.
I start by identifying the wall and every service route before deciding how to frame the cavity. That order helps avoid a common mistake: making room for a pipe or cable, then discovering the route weakens a stud, blocks a valve, or disrupts a rated wall.
What a drywall utility chase is
A drywall chase is a purpose-built, finishable space for routing utilities inside or alongside a wall. It may fit between studs, sit in front of an existing wall, or run vertically or horizontally. The term describes the cavity, not permission to conceal anything that must remain accessible.
A chase can contain electrical cable, plumbing, or mechanical services when the route complies with the applicable codes and product listings. A shallow chase may only cover a small cable run; a larger one may need its own framing and a wider finished wall.
The difference between a chase and a random void is planning. A designed chase has known dimensions, supports, clearances, fireblocking, and access points. Its framing must not be treated as expendable simply because it will be hidden.
Plan the Chase Route and Confirm Code Constraints
Planning means mapping the utilities, framing, and wall requirements before work starts. Confirm whether the wall is bearing, braced, or part of a fire-resistance-rated assembly. Then check the locally adopted IRC or IBC, NEC, plumbing and mechanical codes, and the instructions for each product in the route.
Survey the wall and services
Before cutting, locate studs, wires, pipes, ducts, and other hidden components. Use plans where available, then verify conditions with suitable inspection tools and careful exploratory openings. Mark the proposed chase path and note where the route crosses floors, ceilings, or other concealed spaces.
Check what the chase must carry. Pipes may need support and a planned slope; ducts need space for their actual outside dimensions and any listed clearance. Electrical cables need protection from nails and screws. Valves, dampers, cleanouts, and other service parts may require access.
| Route condition | What to check | Planning response |
|---|---|---|
| Wall may be bearing or braced | Wall function and framing limits | Avoid cuts unless the adopted code or an approved design permits them |
| Cable near a nailing surface | Cable setback from framing edge | Use required steel protection where applicable |
| Pipe, valve, or cleanout in chase | Support and service access | Keep service parts reachable |
| Rated wall or floor assembly | Approved assembly details | Do not alter without an accepted detail |
A chase that crosses a rated assembly needs special care. An unapproved opening or finish can affect the assembly’s fire-resistance rating. Confirm the required construction and penetration protection before framing.
Check Framing, Utility Clearances, and Service Access
Framing limits protect the wall’s capacity, while clearances protect utilities and equipment. The numbers below are common IRC and NEC provisions, not a substitute for checking the adopted edition, exceptions, engineered framing rules, or local amendments. Do not apply standard stud rules automatically to engineered members.
Apply boring and notching limits carefully
Under IRC R602.6, a hole in a stud generally cannot exceed 40% of the stud’s width. Up to 60% is allowed in nonbearing walls and in specified doubled-stud conditions. Keep the hole edge at least ⅝ inch from the stud edge. Conditions and exceptions apply, so check the adopted text.
For notches, the general maximum is 25% of stud width in bearing walls and 40% in nonbearing walls. These limits are not a green light to cut any stud. Braced-wall elements, engineered members, and other restricted framing may need separate approval or design.
If the route cannot fit within permitted framing limits, change the chase design rather than enlarging the cut. Options may include a separate framed fur-out, a different route, or a design approved by the responsible building professional.
Protect cables and preserve access
NEC 300.4(A)(1) addresses cables near framing edges that could be struck by fasteners. Where a bored hole is closer than 1¼ inches to such an edge, protect the cable with a steel plate at least 1⁄16 inch thick, subject to the adopted NEC edition and applicable exceptions. A plate does not make an excessive or misplaced framing cut acceptable.
A junction box must remain accessible under NEC 314.29. In practical terms, do not bury a box behind permanent drywall. Plan an approved access panel or place the box where it remains reachable. Apply the same principle to valves, dampers, cleanouts, and other parts that must be serviced.
Frame, Protect, Fireblock, and Rough-In
This stage turns the plan into a safe cavity. Frame the chase without unauthorized structural cuts, fit the utilities with their required supports and clearances, and install protection and fireblocking. Work that requires a licensed trade or inspection must follow local rules.
Build the cavity around the route
Set chase depth and width from the largest service, including supports, fittings, and required clearances. Allow room to install and inspect the service without forcing it against the drywall. Use framing that provides a stable drywall edge and does not interfere with openings or other wall functions.
Keep utilities separated where their codes, listings, or installation instructions require it. Use approved plates to protect cables from fasteners. Support pipes, cables, and ducts as required for their type and route; a chase is not a substitute for proper support.
Install fireblocking and protect rated assemblies
IRC R302.11 requires fireblocking at specified concealed-space boundaries, including at floor and ceiling levels and at intervals not exceeding 10 feet vertically in stud walls. Use only materials and methods permitted by the adopted code, and seal penetrations as required.
A chase can create a long concealed path for fire and smoke if it is not blocked where required. Plan each floor, ceiling, and wall transition before rough-in. If the chase affects a rated assembly, use an approved assembly detail and required penetration protection; do not assume ordinary drywall repairs preserve the rating.
Inspect, Document, and Close the Chase
Before drywall covers the work, verify the route, protections, supports, fireblocking, and access points. Photograph the open chase and arrange required inspections. Closing the wall is the final step, not a way to resolve missing access or uncertain code details.
Use a pre-close checklist
- Confirm the route matches the approved plan and does not exceed framing limits.
- Check cable protection plates, service supports, and required clearances.
- Verify fireblocking and penetration protection at each required location.
- Confirm every required junction box and service component remains accessible.
- Complete permits and inspections required by the local authority.
- Save photos and measurements showing concealed work before installing drywall.
When finishing, keep access panels clear and do not cover openings with trim or built-ins. For a rated wall, follow the required assembly and finish details. If inspection reveals a problem, correct it before closing the chase.
Example Chase Scenarios
These examples are illustrative planning cases, not reports of specific jobs. They show how the same method applies to different routes. Actual dimensions and code requirements depend on the building, utilities, product listings, and locally adopted rules.
Vertical cable route in a stud wall
Suppose a homeowner wants to route cable from one floor to another. I would first identify the wall’s role, confirm the route avoids restricted framing, and check cable setback from nailing edges. The plan would also show required fireblocking and any accessible boxes before drywall goes up.
Plumbing line beside an existing wall
A homeowner may build a shallow fur-out to avoid cutting studs for a new pipe. The chase depth should account for pipe diameter, fittings, supports, and access to any valve or cleanout. If the wall is rated or structural, the fur-out does not remove the need to protect the original assembly.
Duct route across a ceiling or wall
A duct chase must fit the duct’s real outside size and retain clearances required by its listing and mechanical code. Framing should support drywall without pinching the duct or blocking service access. Confirm fireblocking and rated-assembly details wherever the path crosses a required boundary.
Common Questions About Drywall Chases
These direct answers cover the most common design and code questions. Always verify the locally adopted code text, permit rules, and product instructions before work, since requirements can vary by location and assembly.
Can I hide a junction box inside a drywall chase?
Only if it remains accessible as required by NEC 314.29. Do not permanently cover it with drywall.
How large can I bore a stud for a utility?
Under the general IRC R602.6 rule, a hole is limited to 40% of stud width, with specified cases allowing up to 60%. Check the adopted code and framing type.
How close can a cable hole be to a stud edge?
The general IRC stud-hole rule requires at least ⅝ inch from the stud edge. NEC cable protection may also apply near fastener surfaces.
When do I need a steel protection plate?
For the condition in NEC 300.4(A)(1), protect cable when a bored hole is closer than 1¼ inches to an edge that could receive fasteners. The plate must be at least 1⁄16 inch thick, subject to local adoption and exceptions.
Can I notch a bearing-wall stud for a pipe?
The general IRC limit is 25% of stud width in a bearing wall. That limit does not automatically apply to engineered or restricted framing. Verify the exact condition before cutting.
How often is fireblocking required in a stud-wall chase?
IRC R302.11 includes fireblocking at specified boundaries and at intervals no greater than 10 feet vertically in stud walls. Confirm permitted materials and details in the adopted code.
Can a chase go in a fire-rated wall?
Potentially, but the chase must preserve the required rated assembly and approved penetration details. Do not assume a new cavity or opening is acceptable without checking the assembly requirements.
Should I install drywall before inspection?
No, not when an inspection is required. Keep the work visible until the required review is complete, and document the route before closing.
A drywall chase is successful when it routes utilities without weakening framing, blocking service, or compromising required fire protection. Plan the path first, use code limits as minimum design checks, and confirm the details against the adopted rules and product instructions. If a route requires a structural cut or affects a rated assembly, get an approved detail before proceeding.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)




