What Is Modular Temporary Shrouding? (Pipe Curtains)
A modular temporary shroud, often called a pipe curtain, is a removable screen that hides exposed piping without becoming a permanent enclosure. Its sections should allow inspection and maintenance, preserve required equipment clearances and ventilation, and avoid concealing hazards. No single code sets a universal pipe-curtain design: local rules, equipment instructions, and the authority having jurisdiction govern.
Exposed pipes can make a finished room feel incomplete, but covering them too tightly can create a more serious problem: blocked access, trapped heat, or a hidden leak. A good pipe curtain balances appearance with inspection and service needs. It should come down in sections, not force a worker to dismantle unrelated parts to reach one valve.
I treat “temporary” as a design feature, not an excuse to skip planning. Before choosing fabric or hardware, identify what the pipes serve, where access is required, and which clearances must stay open. The examples below are illustrative layouts, not claims about specific completed projects or code approvals.
Survey the Pipework, Hazards, and Applicable Requirements
A pipe survey records what each line carries, what can move or heat up, and where inspection is needed. It also identifies nearby equipment that may set stricter rules than the curtain itself. Make this assessment before measuring panels or buying supports; the layout depends on the hazards and access points.
Walk the route and note the pipe service, insulation, temperature concerns, supports, labels, valves, unions, cleanouts, and likely leak points. Include nearby electrical panels, sprinklers, smoke detectors, air intakes, and combustion equipment. If a line’s purpose is unclear, ask a qualified tradesperson rather than guessing from its appearance.
Then check the locally adopted building, fire, plumbing, mechanical, and electrical codes, along with equipment listings and manufacturer instructions. Ask the authority having jurisdiction (AHJ) when requirements are unclear. There is no universal pipe-to-fabric offset, airflow allowance, or curtain-support capacity that works for every installation.
Textile fire performance is a separate question. NFPA 701 sets test methods for flame propagation of textiles and films; it is not a universal requirement for every pipe curtain, and passing it does not make a curtain fire-rated. Use compliant test documentation when the adopted code, venue, or AHJ requires it.
If a project specifically requires an ASTM E84 classification, Class A uses a flame-spread index of 0–25 and a smoke-developed index of 0–450 under that standard’s classification scheme. Those surface-burning results do not prove NFPA 701 compliance or authorize use where a curtain is prohibited.
Preserve Service Access and Required Clearances
A curtain is acceptable only when it leaves required working space and access usable. “Removable” must mean that the relevant panel can be taken away without shifting pipes, damaging insulation, or removing unrelated sections. Keep critical labels and visible signs of leakage in view or readily inspectable.
For electrical equipment where the NEC applies, Section 110.26(A)(1) sets working-space depth at 3–4 feet, depending on voltage and exposure conditions. Width must be at least 30 inches or the equipment width, whichever is greater; height is generally at least 6.5 feet or the equipment height, whichever is greater. A curtain may not intrude into required working space. Verify the adopted edition and local amendments.
NEC 110.26(E)(1)(a) also reserves dedicated equipment space above qualifying panelboards and switchboards. Do not place curtain supports or route foreign systems in portions of that space where prohibited. The exact provisions and dimensions depend on the adopted code, so check the applicable edition rather than relying on a generic sketch.
Plan openings around service points. A valve should be operable; a cleanout or union should be reachable; and an inspection point should not disappear behind a fixed panel. Where access must be frequent, use a section that can be released independently and returned to the same position.
Combustion equipment and hot piping need special care. A curtain can trap heat, obstruct combustion or ventilation air, or hide a hot surface or leak. There is no generic safe fabric distance or CFM allowance. Follow the appliance and pipe manufacturer’s clearances and ventilation requirements, and seek AHJ review if the screen could affect them. Ordinary flame-tested fabric is not a fire barrier.
Install Modular Supports and Removable Curtain Panels
A modular layout divides the screen into manageable sections that can be removed separately. Each panel needs a clear removal path, suitable support, and enough clearance to avoid contact with pipes or insulation. The support system must attach to a suitable building surface, not rely on the piping to carry the load.
Set panel boundaries. Mark pipe runs, valves, joints, cleanouts, and inspection points. Place seams where a worker can reach the relevant feature without taking down other panels. Avoid creating a closed top or bottom if that would impair ventilation or conceal a hazard.
Choose the mounting surface. Identify the actual substrate, such as framing or masonry, and use hardware rated by its manufacturer for that substrate and the expected loading. Select based on the manufacturer’s rated working load for the real installation, not on appearance or an assumed capacity. If the substrate or load is uncertain, get qualified advice.
Keep supports independent. Do not fasten a curtain to piping, insulation, sprinkler components, electrical equipment, or other services unless that component’s manufacturer expressly permits the load. Do not let fabric rest on hot lines or compress insulation. A support attached to a suitable building element should carry the curtain without transferring load to services.
Fit and test each section. Use compatible, cleanable material appropriate to the location and any required fire-test documentation. Install panels so the removal method is obvious to the person who will inspect or service the pipes. Test removal and replacement before calling the work complete.
| Design choice | Suitable when | Check before installing |
|---|---|---|
| Separate small panels | Valves or joints need frequent access | Each section releases without disturbing adjacent sections |
| One long panel | The run is simple and has few service points | Panel weight, support rating, and removal path |
| Open top or bottom | Needed to preserve airflow or visibility | No required clearance, ventilation, or hazard is compromised |
| Flame-test-documented textile | Documentation is required by the site or AHJ | The specified test and product documentation match the requirement |
Verify Stability, Access, and Fire-Safety Documentation
Verification means checking the finished screen against the survey and the requirements that applied before installation. A neat appearance is not enough. Confirm that supports are secure, panels release as planned, access remains clear, and any required product documentation is available to the owner or maintenance team.
Check the installation in this order:
- Confirm the curtain does not enter required electrical working or dedicated space, or other equipment clearances.
- Check that supports attach to the intended substrate and that no load rests on piping, insulation, sprinklers, or electrical equipment.
- Remove and replace each panel using the planned method. Make sure the route to each valve, joint, cleanout, and inspection point is usable.
- Look for blocked labels, hidden leak indicators, trapped heat, or interference with ventilation.
- Keep any required flame-test documentation with the project records. Do not describe a textile as “fire-rated” merely because it passed a flame-propagation test.
Record what the curtain covers, how it comes off, and who is responsible for removing it during inspection or service. Recheck the installation after plumbing changes, maintenance, or changes to nearby equipment. A panel that once cleared a valve may no longer do so after the pipe layout changes.
Example Layouts and Planning Checks
These examples show how the same modular idea changes with the pipework. They are planning scenarios, not code approvals or universal dimensions. In each case, confirm site-specific clearances and requirements before installing a screen.
Utility-room valve cluster: Several valves sit along an exposed water line. A single fixed sheet would hide them, so the layout uses separate removable panels aligned with the service points. The key check is whether each valve can be operated and inspected without removing unrelated sections.
Pipe run near a panelboard: A screen might improve the room’s appearance but cannot occupy the electrical working space or prohibited dedicated space. The planning decision is to stop or reroute the curtain outside those areas, then verify the result against the adopted NEC edition and local amendments.
Hot pipe near combustion equipment: A fabric screen could affect heat release or air supply. Do not choose an offset by rule of thumb. Check manufacturer instructions and required ventilation, then ask the AHJ if the proposed screen may affect equipment operation or safety.
These scenarios illustrate the main trade-off: panel size, appearance, and convenience come after access, clearances, and safe operation.
Frequently Asked Questions
These answers summarize the core planning points for a temporary pipe shroud. Local code, the pipe or appliance manufacturer, and the AHJ may add requirements. When those sources differ from a general guide, verify the rule that applies to the specific installation before proceeding.
Is a pipe curtain the same as a pipe enclosure?
No. A pipe curtain is a removable screen. It is not automatically an enclosure, fire barrier, or rated assembly.
Is there a code that defines a universal pipe curtain?
No single code sets a universal pipe-curtain specification. Applicable local codes, manufacturer instructions, and AHJ decisions govern.
How far should the curtain be from the pipe?
There is no universal offset. Use the pipe or equipment manufacturer’s clearance requirements and account for inspection, movement, heat, and site conditions.
Can I hang a curtain from a pipe?
Not unless the component manufacturer expressly permits the added load. Use independently supported hardware attached to a suitable building surface.
Can a curtain cover a valve or cleanout?
It may screen the area only if the service point remains reachable as required. Design a removable section that gives access without dismantling unrelated panels.
Does NFPA 701 make a pipe curtain fire-rated?
No. NFPA 701 provides flame-propagation test methods for textiles and films. Passing it does not create a fire-resistance rating.
Does ASTM E84 Class A mean a textile passes NFPA 701?
No. The standards address different test methods. One result does not establish compliance with the other.
Can a pipe curtain go in front of an electrical panel?
Not if it intrudes into required electrical working space or a prohibited dedicated space. Check the adopted NEC edition and local amendments.
Can a curtain surround combustion equipment or hot piping?
Only after confirming manufacturer clearances and ventilation provisions. If the screen may affect them, obtain AHJ review; do not assume a generic fabric distance is safe.
What should I inspect after installation?
Check attachment, stability, clearances, panel removal, service access, labels, leak visibility, ventilation, and any required fire-test documents. Recheck after system changes or maintenance.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)





