Hide Bagpipe Gear (L&M Concealment Cases)
A discreet cabinet can keep an L&M bagpipe case out of sight while leaving it easy to reach and protecting the instrument. Start by measuring the actual loaded case, then plan the cabinet opening, shelf, and removal path around it. Use manufacturer instructions and local building requirements; do not cut into a wall or guess at ventilation needs.
If you remember pipes being brought out for a family gathering, a parade, or a lesson, you know the case is part of the routine. But when it is not in use, a large case can dominate a room or hallway. A cabinet can make storage feel more settled without making the instrument hard to get to.
The best concealment is practical, not sealed away. I plan around the case that is actually on hand, the route it must travel, and the wall or floor that will support the cabinet. L&M case dimensions and loaded weight vary by model, so a product name alone is not enough to size a cabinet. The measurements and load targets below are planning guidance, not code requirements.
Planning and Case Survey
A case survey records its full outside dimensions, loaded weight, and the conditions around the proposed cabinet. It also checks the room, access route, and nearby services before any building work starts. These details help prevent a cabinet that looks right but cannot safely hold or release the case.
Measure the complete case
Measure the outside envelope: the greatest width, height, and depth, including handles, straps, feet, and any other protrusions. If a strap can hang loose, note its position when the case is stored. Use those measurements, not an assumed L&M specification.
Weigh the case with everything that will stay inside it. If a scale cannot safely take the full load, weigh the case and contents separately and add the results. Record the model or product label if available, but confirm dimensions yourself.
Also inspect the case. Note whether its shell, handles, or straps need room to avoid pressure or snagging. If the instrument is stored inside the case, keep the case closed as its maker directs.
Survey the proposed location
Check the whole route from the room entrance to the cabinet. Measure narrow doorways, turns, stair landings, and the final approach. A case that fits inside a cabinet may still be awkward to put away if the approach requires a sharp turn.
Look for studs, plumbing, wiring, and other services before fastening or opening a wall. Note nearby heaters, damp surfaces, and places where water may collect. Confirm that doors, drawers, and walkways will remain usable.
Next step: Keep a written list of case measurements, loaded weight, location hazards, and the direction the case will travel.
Access Path and Clearances
Clearance is the free space around the case that lets it enter and leave without catching or scraping. The cabinet opening must fit the case’s widest measured dimension, and the route must allow the case to turn or slide into position. These are design checks, not universal building-code dimensions.
Size the opening and interior
As a design target, allow at least 25 mm of clearance on each side of the measured case envelope. Size the clear opening to the case’s widest dimension plus 50 mm. Check both figures against the actual removal path; an opening that is wide enough on paper may not work when the case must be tilted or turned.
Measure clear space inside the cabinet, not just its outside size. Hinges, door stops, trim, shelf edges, and handles can reduce the usable opening. Test the planned path with a cardboard template or a careful mock-up, and avoid forcing the case around a tight corner.
| Check | Planning target | What to verify |
|---|---|---|
| Side clearance | At least 25 mm per side | Full case envelope, including protrusions |
| Clear opening width | Widest case dimension + 50 mm | Actual entry and removal path |
| Interior depth and height | Case dimension plus needed handling room | Door hardware and shelf position |
| Shelf capacity | At least 2× loaded case weight | Rating for the installed span and support method |
The side and opening targets are not substitutes for a full fit test. Confirm that the case can be lifted or slid out safely, with enough hand room to grip it. If you need to rotate the case, check the turning space as well as the opening width.
Next step: Mark the opening and shelf positions, then test the route with a same-size template before ordering or building the cabinet.
Cabinet Construction and Installation
A cabinet may be freestanding or attached to a wall or other suitable support. Choose the least disruptive option that fits the room and holds the loaded case. Follow the cabinet and fastener makers’ instructions, and check local requirements before altering walls, floors, or built-in assemblies.
Choose a cabinet location and type
A freestanding cabinet can avoid opening a wall. It still needs to remain stable and be positioned according to its manufacturer’s instructions. A surface-mounted cabinet may work where secure framing or an appropriately rated backing system is available.
A recessed cabinet can look integrated, but it carries added risk. Cutting into studs or a rated wall assembly may affect structure, fireblocking, or fire protection. A wall cavity may also hide wiring or plumbing. Do not cut or cover these elements without confirming local requirements and an approved detail.
Anchor and support it responsibly
Anchor the cabinet to verified framing or an appropriately rated backing system. Select fasteners using the published load data from the cabinet or anchor manufacturer, and install them as directed. Do not assume a fastener’s load rating applies to every wall material, spacing, or installation method.
For the shelf and its supports, use a rating of at least 2× the measured fully loaded case weight as a design target. Confirm that the published rating applies to the shelf span and support method you will use. This is a planning margin, not a code rule or a guarantee against failure.
Do not drill until you have checked for services and confirmed the intended fixing points. If the location or wall construction is uncertain, pause and get qualified help rather than guessing.
Next step: Choose the cabinet and anchorage only after you can identify the support, fastener data, shelf rating, and installation method.
Load, Access, and Moisture Verification
Verification means testing the installed cabinet with the real case before relying on it. Check that the shelf stays stable, the cabinet does not shift, and the case can be removed without catching. Also consider moisture: there is no universal airflow rate for this storage use, so avoid sealed spaces that may trap dampness.
Load and test the cabinet
Follow the installation instructions, then place the loaded case on the shelf in a controlled way. Watch for shelf movement, visible bending, fastener movement, or cabinet shift. If anything moves or feels unstable, remove the case and reassess the support rather than continuing to load it.
Open and close the cabinet door, then remove and replace the case along the planned route. Check for contact with hinges, trim, handles, or other gear. The case should not have to be squeezed into place or lifted by a strap unless the case maker permits that handling.
Keep the storage area suitable
There is no generally applicable CFM requirement for a bagpipe-storage cabinet. CFM means cubic feet of air moved per minute, but choosing a fan rate without a defined moisture load and safe discharge path would be guesswork. Do not add a fan merely to create a number on a plan.
Keep the case clear of heaters and damp surfaces. Do not seal it inside an unventilated wall cavity. If the room or case is damp, address the source and follow the instrument and case makers’ care instructions before storing it.
Next step: After testing, confirm that the case is dry, the cabinet is stable, and its opening remains clear.
Worked Planning Examples
These examples show how to apply the measurement method; they are not reports of completed installations or claims about a specific L&M model. The figures are hypothetical and illustrate the formulas only. Measure your own case and check the actual cabinet and fastener ratings before proceeding.
Example: opening width
Suppose a measured case is 600 mm wide at its widest point, including handles. The design target for a clear opening is 600 mm plus 50 mm, or 650 mm. The cabinet still needs to provide enough room for the case’s full height and depth, along with its actual approach and removal path.
If a hinge or door stop reduces the clear opening to 630 mm, the cabinet does not meet that target, even if its outside width appears generous. The next step is to change the cabinet or its door layout, then check the path again.
Example: shelf load target
Suppose the fully loaded case weighs 18 kg. The shelf and supports should have a published rating of at least twice that measured weight: 36 kg or more for the installed span and support method. That figure is a design target, not a universal code requirement.
If the manufacturer’s rating applies to a shorter span than the planned shelf, do not treat it as proof that the shelf is suitable. Find a rating that matches the actual setup or choose a different support arrangement.
Common Questions
These short answers address the main decisions involved in choosing and fitting a cabinet for a bagpipe case. Use them as a final check, not as a substitute for the case, cabinet, and fastener instructions or local building requirements.
Can I use a standard cabinet for an L&M case?
Possibly, if the actual case fits with handling room and the cabinet is rated for the load. Measure the case and compare its size with the cabinet’s clear interior and opening.
Are all L&M case dimensions the same?
Do not assume so. Confirm the exact model and measure the complete case, including handles, straps, and protrusions.
How much clearance should I allow?
As a design target, allow at least 25 mm on each side of the measured case envelope. Check the full removal path too.
How wide should the cabinet opening be?
Use the case’s widest measured dimension plus 50 mm as a design target. Confirm that the case can pass through along its intended path.
How strong should the shelf be?
Target a shelf and support rating of at least twice the fully loaded case weight. The published rating must match the installed span and support method.
Does the cabinet need a fan?
There is no general CFM requirement for this use. Do not select a fan rate without a known moisture load and safe discharge path.
Can I recess the cabinet into a wall?
Only after checking for wiring, plumbing, structural framing, fireblocking, and any rated wall requirements. Do not cut into an assembly without an approved, code-compliant detail.
Should the case touch a heater or damp wall?
No. Keep it clear of heaters and damp surfaces, and follow the case and instrument makers’ care guidance.
How do I check the cabinet after installation?
Test it with the loaded case. Look for shelf deflection, movement at the anchors, and any obstruction when opening, loading, or removing the case.
Final Check Before Use
A well-planned cabinet hides the case without hiding the practical details that matter: its real dimensions, loaded weight, support, and route in and out. Use the actual L&M case as your template, treat the clearance and load figures as design targets, and confirm published ratings for the installed setup.
Before loading it, verify the anchorage, shelf, door opening, and removal path. Keep the storage area away from heat and damp, and do not create a sealed wall cavity or alter a rated assembly without an approved detail. If any measurement, support, or service location is uncertain, resolve it before construction.
(This article was written by one of our staff writers, Ethan Caldwell. Visit our Meet the Team page.)






