Hide Wall Phone Jack (Blank Cover Plate Art)
To disguise an inactive wall phone jack, replace its working faceplate with a compatible blank cover, then apply artwork to the cover or add a removable art panel. Keep the box accessible, preserve the cable, and avoid permanent paint, caulk, or finishes across the cover seam. If the jack is active, choose art that leaves its opening clear.
A quick visual fix is often simple: match a blank cover to the wall color, or turn it into a small, removable art feature. The important distinction is whether the jack still needs to work. A decorative cover can hide the outlet from view, but it must not make the wiring box unreachable.
In my work, I have found that the best results come from treating the cover as a small piece of finish, not as a reason to close up the wall. A neat edge and a removable attachment usually look more intentional than a picture hung over the jack.
Planning: identify the jack and choose the right cover
An inactive phone jack can usually be covered with a blank plate secured to the existing box. First confirm that the outlet is for telephone or communications wiring, not a mains-voltage receptacle. Then decide whether it must stay usable, check the plate and screw locations, and select a finish that can be removed without damaging the wall.
Confirm whether the jack is active
A phone jack is the connection point for a telephone line. “Active” means the line is still connected and may be needed for a phone, modem, alarm, or other equipment. If you are unsure, do not assume the jack is unused just because nothing is plugged into it.
An active jack needs a faceplate with an opening that fits the jack. You can make the plate less noticeable with color, a compatible decorative faceplate, or a removable piece of art that does not block the opening. Do not put a blank cover over a jack that still needs to be used.
If you plan to retire the line, have it properly disconnected and the conductors secured. Telephone wiring can carry ringing voltage, which may be hazardous. If the wiring type or status is unclear, ask a qualified communications or electrical professional to identify it before you handle it.
Measure before ordering
Common single-gang wall plates are nominally 2.75 by 4.50 inches. That is a useful starting point, not a guarantee of fit. Measure the existing plate, note the box opening, and check the position of the screw holes before buying a blank plate or ordering custom artwork.
The common center-to-center spacing for single-gang device-yoke screws is 3.281 inches, or about 83.3 mm. Blank plates and specialty covers may differ, so use the actual plate and box as your guide. A cover that looks close in a product photo may not align with the existing screw locations.
| Option | Best for | What to check |
|---|---|---|
| Blank single-gang plate | An inactive jack you want to cover plainly | Plate size, screw alignment, and box fit |
| Decorative plate with jack opening | A jack that must remain usable | Opening size and compatibility with the jack |
| Artwork applied to the blank plate | A small, low-profile visual disguise | That screws and the plate edge remain clear |
| Removable art panel over the plate | A more noticeable art treatment | That the panel comes off without wall damage |
Measure twice, and use the existing cover as a template when practical. If the box is damaged, loose, or crowded with wiring, pause before adding any decorative layer.
Access and clearances: keep the box serviceable
“Accessible” means a person can reach the wiring box without cutting, breaking, or removing the wall or other permanent finish. The adopted NEC 314.29 sets this basic principle for wiring boxes, while NEC 800.24 addresses communications wiring installed in a workmanlike manner. Check the locally adopted code and amendments with your authority having jurisdiction.
Inspect the opening before covering it
Remove the existing plate only if you can do so safely and without disturbing the wiring. Look for damage, loose conductors, or signs that the box may contain wiring beyond the phone connection. Do not tug on the cable or push it deeper into the wall to make room for a cover.
If you find damaged insulation, loose wiring, an unfamiliar cable, or a box that moves when touched, stop and get qualified help. A blank plate is not a repair for a damaged box or cable. Keep the original cable and its terminations in place unless a qualified person is disconnecting them as part of the work.
Make the artwork removable
The cover screws must remain reachable, and the box opening must remain accessible. Apply artwork to the face of the blank cover, or use a separate art panel that can be removed without damaging the wall. Do not let adhesive, paint, or caulk bridge the cover-to-wall seam.
There is no general phone-jack airflow or CFM requirement. Still, do not treat that as permission to pack the box or cable behind a tight decorative assembly. Follow the cover and cable manufacturers’ instructions, and leave the existing wiring undisturbed. Do not assume a universal cable bend radius or cover load rating.
A useful design test is simple: can someone remove the art, reach the plate screws, and remove the cover without cutting or scraping wall finish? If not, revise the attachment before installation.
Execution: install a blank cover and add art
For an inactive jack, use a blank cover that fits the existing box and fastens at the intended screw points. Keep the artwork on the cover or on a separately removable panel. For an active jack, use a compatible faceplate with the required opening. In either case, do not drill through the cover or wall near concealed wiring.
Step-by-step for an inactive jack
- Confirm the line is no longer needed. If its status is uncertain, have it checked before covering it. If it is being decommissioned, make sure it is disconnected and conductors are secured.
- Remove the old plate carefully. Keep track of its screws, and do not pull or twist the cable.
- Check the box and wiring. Stop if you see damage, loose conductors, or wiring you cannot identify.
- Fit the blank cover. Align it with the existing box and screw locations. Secure it with the intended screws, without forcing a mismatched plate.
- Add the artwork. Apply it to the plate itself, or attach a separate panel in a way that allows removal. Keep the plate edges and screw heads accessible.
- Test access. Remove the art panel, then confirm that the cover can be unscrewed without disturbing the wall finish.
Avoid permanent adhesive, caulk, or paint across the plate seam. Do not bury cable ends or splices behind wall finish, and do not fasten artwork through the plate or wall where a fastener could contact concealed wiring.
Choose a finish that suits the wall
A painted blank cover can blend into a painted wall, while a small printed image or graphic can make the plate feel intentional. Before applying paint or adhesive, check that the cover manufacturer permits it. Keep coatings thin enough that they do not bond the plate to the wall or fill its edges.
For a separate art panel, use a light, removable attachment that does not rely on screws through the wall near the box. The panel should lift away cleanly and leave the cover in place. Do not assume a cover has a particular load rating; follow its manufacturer’s instructions and avoid hanging anything heavy from it.
Common choices and trade-offs
| Finish approach | Visual effect | Access considerations |
|---|---|---|
| Wall-color blank plate | Subtle and simple | Plate screws stay visible and reachable |
| Artwork on the plate | Makes the cover a small design detail | Artwork may need to be removed before unscrewing |
| Removable art panel | Can hide the plate from direct view | Panel must come off without wall damage |
| Paint or caulk across the seam | Can look seamless at first | Can make the cover difficult to remove; avoid |
The cleanest option is not always the one that hides the plate most completely. Choose a finish that conceals it at a glance but still makes future access clear and practical.
Real-world design scenarios and verification
These examples show how the same cover can suit different rooms without blocking access. They are design scenarios, not claims about a particular home or code inspection. In each case, the key checks are the same: confirm whether the jack is active, keep the box reachable, and avoid damage to wiring or wall finish.
Scenario: a blank plate on a living-room wall
A homeowner wants to remove the visual distraction of an unused jack beside a framed print. A matching blank plate is secured to the existing box, and a small artwork treatment is applied to the plate. The art is cut or positioned so it does not cover the screw heads or bridge the plate edge.
Scenario: a decorative panel over a plate in a hallway
An interior designer wants a small graphic to tie a hallway wall together. A removable panel sits over the blank cover but is not screwed into the wall near the wiring. It lifts away without scraping paint, leaving the cover accessible.
The important detail is the attachment, not the artwork. If the panel requires permanent adhesive or wall damage to remove, it does not meet the access goal. Choose another mounting method or apply the art directly to the blank cover instead.
Final check before calling it done
Look at the finished wall from normal viewing distance, then check it close up. The plate should sit securely, the art should not conceal the cover seam permanently, and the box should remain reachable without removing wall finish. If the jack is active, confirm that its opening is still clear and usable.
The “low voltage” label does not make a phone box safe to plaster over or seal behind permanent finish. NEC 314.29 requires wiring boxes to remain accessible under the adopted code. A removable decorative treatment is different from permanent concealment, but local requirements can vary. Check the locally adopted NEC edition and any local amendments with the authority having jurisdiction.
Conclusion and FAQ: keep the disguise removable
A blank plate can make an unused phone jack far less noticeable, and artwork can help it blend with the room. The reliable method is to match the cover to the box, preserve the cable and terminations, and keep the plate removable. When in doubt about the wiring or local rules, get the box checked before finishing the wall.
Can I cover an unused phone jack with a blank plate?
Yes, if it is truly inactive and the blank plate fits the existing box. Keep the cover removable and the box accessible.
Can I put a blank plate over a phone jack I still use?
No. Use a compatible faceplate that leaves the jack opening clear, or the connection will not be usable.
Can I paint over the phone jack cover?
You can apply paint only if the cover manufacturer allows it. Do not paint across the cover-to-wall seam or seal the plate in place.
Can I hang a picture over the phone jack?
A removable picture or art panel may work if it comes away without wall damage and does not prevent access to the cover screws. Do not fasten it through the plate or wall near concealed wiring.
What size blank phone-jack cover do I need?
Many single-gang plates are about 2.75 by 4.50 inches, but sizes and screw positions vary. Measure the existing plate and box before ordering.
Are phone-jack plate screws always 3.281 inches apart?
That is a common single-gang device-yoke screw spacing, measured center to center. Blank plates and specialty covers may differ, so verify the actual screw locations.
Is it safe to leave disconnected phone wires inside the box?
Do not leave conductors loose or assume they are safe. Have the line properly disconnected and the conductors secured by someone qualified if you are decommissioning it.
Can I plaster over an old phone jack?
No. A low-voltage phone box is not automatically exempt from access rules. Do not conceal it behind permanent wall finish; check the locally adopted code.
Does a phone jack need ventilation behind its cover?
There is no general phone-jack airflow or CFM requirement. Do not infer that the box can be packed or altered; follow the cover and cable manufacturers’ instructions.
Should I drill the blank plate to attach artwork?
No. Avoid drilling through the plate or wall near concealed wiring. Apply artwork to the cover surface or use a separate removable panel.
(This article was written by one of our staff writers, Michael Donovan. Visit our Meet the Team page.)






