Hide DVD Player in Media Storage (False Books)
A DVD player can sit behind a hinged, book-like cabinet front if the enclosure preserves the clearances and airflow stated in its manual. Build a supported shelf, keep the player’s vents and controls clear, and make the unit easy to remove. Keep its power cord accessible, never inside a wall cavity, and test cooling with the façade closed.
A tidy media cabinet is easier to dust and keep orderly when the player and its cables are not exposed. But a convincing false-book front is more than decoration: the space behind it must stay cool, allow remote control, and provide access for repairs. I plan the cabinet around the player first, then fit the book-like façade to that space.
The technical terms are simple. Clearance is the open space the manufacturer requires around the player. Service access means being able to reach and remove the unit without taking apart the cabinet. Before cutting or building, check the player’s manual and the cabinet’s construction.
Plan the Player Envelope and Ventilation
The player envelope is the full space the unit needs, including its required air gaps and the room needed to connect or remove it. Measure the player and read its manual before setting shelf height or façade size. A book-style cover must not shrink this working space or block the path that cools the player.
Measure the unit and its airflow
Record the player’s width, height, depth, and weight. Note where air enters and leaves, where the power and signal connections sit, and whether the disc tray, buttons, or remote sensor are on the front. The manual’s clearance directions take priority; listed equipment must be installed and used according to the instructions that apply to it (NEC 110.3(B), where adopted).
Use the manual’s stated top, side, and rear clearances when laying out the opening. If it gives no clearance figures, use 50 mm (2 in) at the sides and top and 100 mm (4 in) at the rear as preliminary layout allowances, not certified minimums. Confirm the final arrangement against the manual and check that the player operates normally before completing the cabinet.
There is no universal airflow or CFM figure for DVD players. Do not seal the compartment. Keep the actual intake and exhaust unobstructed, and follow the manufacturer’s ventilation directions. A perforated book-like front does not prove that air can move through the whole compartment, especially if a solid back panel or tightly packed contents block the route.
Draw the full opening and removal path
The clear opening must be at least the player’s width and height plus the specified clearances. Also allow enough depth for the cables and enough room to pull the player out. Mark this full space on the cabinet before building; check that shelves, trim, and hinge hardware do not intrude into it.
In a common planning scenario, a player has a rear exhaust and a front disc tray. A false-book front may look open while closed, yet a solid rear panel can trap warm air. I treat the closed-front arrangement as the real design condition, not the more spacious view with the façade open.
Preserve Clearances, Controls, and Service Access
A façade is the hinged or removable book-like front that hides the player. It should conceal the equipment without interfering with cooling, the disc tray, controls, or cables. Plan how you will use the player and take it out before choosing the hinge position or finishing the cabinet.
Check remote control and disc access
Test whether the remote works through the closed façade. If the front blocks the player’s infrared (IR) receiver, an IR repeater can carry the remote signal to the equipment. Confirm that the selected repeater works with the player and that the receiver and transmitter can be positioned as their instructions require.
Make sure the front can open far enough to reach the tray and buttons. The player should also slide out without dismantling the cabinet. If the player’s front must be exposed while a disc is loaded, design the façade to open fully and stay clear of the tray.
Route cables without creating a hazard
Provide openings for signal and power cables with smooth edges so they do not rub against sharp material. Use suitable strain relief where needed to reduce pull on connectors. Leave enough slack to withdraw the player, but keep cables from crossing vents or catching in the hinge.
Keep the player’s power cord accessible and out of walls or other concealed building cavities. Do not route an extension cord through a wall or hidden cavity. Follow the equipment instructions and locally adopted electrical and building codes; if the setup requires a new receptacle or changes to building wiring, consult a qualified electrician.
Build the Shelf and False-Book Façade
The shelf carries the player; the false-book trim hides it. Use a stable shelf and supports suited to the cabinet and its material. Treat the decorative façade as non-load-bearing, and make its hinges secure enough for its own weight and repeated opening without letting it press against the player.
Support the player securely
Use at least 18 mm (¾ in) plywood for the equipment shelf. Select supports rated for at least twice the combined weight of the shelf and player. Check that the rating applies to the support’s installed orientation, spacing, and substrate; a rating alone does not confirm that an attachment is suitable for every cabinet.
Anchor supports to sound cabinet material and verify that they do not shift under load. Do not rely on the book-like trim to hold the shelf or player. Leave the manual-required clearance around the player after the shelf, supports, and cable openings are in place.
Allow a fabrication tolerance of ±1.5 mm (¹⁄₁₆ in) while cutting and fitting parts. This is a workmanship allowance, not extra clearance to subtract from the required opening. Recheck the finished opening against the player’s dimensions and manual before installing the façade.
Fit a ventilated, serviceable front
A hinged or removable front makes routine access easier. Position hinges so the façade opens without hitting the player, tray, or nearby cabinet doors. Keep any perforations or ventilation openings clear of fabric, books, foam, and decorative panels that could obstruct air.
A false-book face can look vented but still have a blocked airflow path behind it. Check the full route from the player’s intake to its exhaust with the façade closed. Do not infer that ventilation is adequate from visible gaps alone; the player’s manual and an operating check guide the final decision.
Compare Practical Layout Choices
This comparison highlights the trade-offs between common cabinet arrangements. The right choice depends on the player’s ventilation direction, the cabinet’s available space, and how often you need access. In every layout, preserve the manual’s clearances and make sure the player can be removed without dismantling the cabinet.
| Layout | Works best when | Check before building |
|---|---|---|
| Hinged false-book front | You want quick access to the tray and controls | Confirm the open front clears the player and the closed front does not block airflow |
| Removable false-book panel | The cabinet has room to lift or remove the panel | Make sure removal is simple and does not pull on connected cables |
| Fixed decorative front with access opening | The player’s controls and disc tray remain reachable through the opening | Check that the opening is large enough and does not obstruct vents or the remote sensor |
The simplest-looking option is not always the easiest to maintain. A hinged or removable front usually makes cleaning, cable checks, and player removal more direct than a fixed cover. Choose the layout that gives you reliable access, not only the one that hides the most.
Verify Cooling, Operation, and Anchorage
Verification means checking the finished setup in its normal, closed-front condition. It covers airflow, remote response, disc access, cable movement, and shelf stability. Run these checks before treating the installation as complete, then repeat them if you change the player, cables, or cabinet contents.
Finish with a closed-front test
With the façade closed, run the player through a representative playback period. Check for signs that heat is building up, confirm the player operates as expected, and make sure the remote works. If the manual calls for a specific ventilation arrangement, compare the finished cabinet with that direction.
Open the front and inspect the intake and exhaust path. Check that cables have not shifted across vents and that the player can still be removed without taking apart the cabinet. Recheck shelf supports and anchorage for movement. If the player behaves abnormally or the cabinet prevents the required airflow, stop using the enclosed arrangement and revise it.
Two planning examples
For a player with a rear exhaust, I would first confirm there is enough rear space and a clear route for warm air to leave. If the cabinet has a solid back, I would not assume that front perforations solve the problem; the actual airflow path needs to meet the player’s instructions.
For a player whose remote sensor is blocked by the closed front, I would test an IR repeater before finishing the façade. In either case, the opening and removal path matter as much as the hidden appearance. These are planning examples, not substitutes for the specific player manual or an on-site assessment.
Next step: measure the player, mark the required clearances and removal path, then choose the shelf and façade design. Do not close the cabinet around a player until you have verified airflow and access.
Frequently Asked Questions
These answers cover the most common decisions when concealing a DVD player behind a book-like cabinet front. The player’s manual and locally adopted codes take priority over general layout guidance, since models and cabinet conditions differ. Use the questions as a final check before building or changing an existing media cabinet.
Can I put a DVD player behind a false-book front?
Yes, if the front does not block required airflow, controls, the disc tray, or service access. Follow the player’s manual, and test operation with the front closed.
How much clearance should I leave?
Use the clearances in the player’s manual. If none are stated, 50 mm (2 in) at the sides and top and 100 mm (4 in) at the rear are preliminary layout allowances, not certified minimums.
Do I need a specific vent size or CFM?
There is no universal CFM requirement for DVD players. Follow the manual, keep intake and exhaust unobstructed, and verify the actual airflow path with the façade closed.
Are holes in the false-book front enough for ventilation?
Not necessarily. A solid back, blocked exhaust, or packed contents can trap heat even when the front has holes. Check the whole path around the player.
Can I hide the player’s power cord inside the wall?
Do not route an extension cord or the player’s power cord through a wall or concealed building cavity. Keep the cord accessible and follow applicable equipment instructions and local code requirements.
What shelf material should I use?
Use at least 18 mm (¾ in) plywood for the equipment shelf. Support it with hardware rated for at least twice the combined shelf and player load, with the rating appropriate for the installation.
How do I use the remote with the front closed?
First test the remote through the closed façade. If the front blocks the player’s IR receiver, use a compatible IR repeater installed according to its instructions.
How can I remove the player for service?
Provide a hinged or removable façade and enough withdrawal space to slide the player out without dismantling the cabinet. Leave cable slack, but keep cords clear of vents and hinges.
What should I check after building the enclosure?
Run the player with the façade closed for a representative playback period. Check operation, heat buildup, remote response, disc access, airflow, cable position, and shelf-support stability.
(This article was written by one of our staff writers, Michael Holloway. Visit our Meet the Team page.)






