Clipboard Phone Stash (DIY Hollow Clipboard)
A clipboard phone pocket is a shallow, open-top holder attached to the back of a clipboard. Measure your phone with its case, build in room for easy removal, and keep the pocket clearly identified and non-locking. This is a storage craft project, not a way to hide a phone or bypass school, exam, or workplace rules.
If you want a place to keep a phone with your notes, a clipboard pocket can make carrying both simpler. My practical pick is a light, shallow pocket made from thin sheet material, with rounded edges and enough clearance to avoid scraping the phone. A cardboard mock-up is the best first step; it helps catch fit and clip problems before you attach anything.
Use the pocket only where phone storage is allowed. It should not obstruct the writing surface, hold a phone while it is charging, or be presented as a secure container. Ordinary craft materials do not provide fire, tamper, or theft protection.
Planning and Phone Measurement
Planning means measuring your actual phone and clipboard before choosing materials or cutting parts. Phone model names are not enough: cases can change both size and shape. A careful survey also checks the clip, board surface, and pocket position so the finished holder stays practical and does not affect normal use.
Measure the phone and board
Measure the phone with its case fitted. Record its length, width, and thickness, including any raised camera area that could catch on the pocket. Use a ruler or caliper, and write the measurements down rather than relying on memory.
For a starting fit, allow at least 3 mm of extra space on each side and 3 mm of extra depth. That means adding 6 mm to the phone’s length and width for the pocket’s clear inside dimensions. Keep the pocket depth no greater than the phone’s thickness plus 3 mm. A much deeper pocket can let the phone shift when you tilt the board.
Measure the clipboard’s back and note the clip’s footprint, movement, and any raised hardware. Decide where the phone can sit without covering a clip, getting in the way of your hand, or making the board awkward to hold. Leave the front writing surface flat and clear.
Choose a permitted use
Before building, consider where you will carry the clipboard. If a class, exam, workplace, or venue restricts phones, follow its rules; do not use a pocket to make a phone harder to see or inspect. If you need a phone for an approved task, ask what storage or use is allowed.
A useful design is clearly recognizable as a pocket, open at the top, and easy to inspect. It is for carrying a phone when permitted, not for concealing one. If that purpose does not fit the setting, use a different storage option.
Access, Clip Interference, and Clearances
Access and clearance describe whether the phone can go in and come out without catching, and whether the pocket stays clear of the clip. A paper or cardboard test piece lets you check both before construction. The goal is a snug, usable fit, not a tight enclosure or a hidden compartment.
Make a paper or cardboard mock-up
Cut a simple pocket shape from scrap paper or thin cardboard. Fold or tape its sides to match your planned inner dimensions, then position it on the back of the clipboard. Try the phone in the mock-up with its case on.
Check these points before moving on:
- The phone slides in and out without force or scraping.
- The pocket stays open at the top and does not cover the camera, buttons, or charging port.
- The phone does not fall out when you gently tilt the board in normal carrying positions.
- The clip opens and closes fully, and the pocket does not touch its moving parts.
- The board still rests flat enough to write on.
If the phone binds, increase the inside dimensions in small steps. If it shifts or slips out, reduce excess space or adjust the pocket’s position. Do not solve a loose fit by making a deep, sealed sleeve; the phone should remain easy to remove.
Set the pocket position
Place the phone where it will not make the board unbalanced or block your grip. Test the clipboard in the way you expect to carry and use it. A pocket that fits on a workbench may feel awkward when the board is held in one hand.
A mock-up can also reveal whether a corner catches on clothing or bags. Round the corners and keep the pocket edges smooth. Take the phone out before writing if the pocket makes the board wobble or prevents it from sitting flat.
Pocket Construction and Finishing
Pocket construction means attaching a shallow backer and pocket face without damaging the clipboard or phone. Use materials that suit the clipboard and follow the adhesive or fastener maker’s instructions. This is a craft assembly, not a tested enclosure, so avoid claims that it is secure, fire-rated, or tamper-resistant.
Select materials
A practical starting point is a rigid backer about 3–6 mm thick and a pocket face about 1–2 mm thick. These are guide dimensions, not universal requirements. Check the chosen sheet material’s instructions and adjust if it bends, cracks, or adds too much weight.
| Part | Starting size or choice | Check before use |
|---|---|---|
| Rigid backer | 3–6 mm | Does it sit flat against the clipboard? |
| Pocket face | 1–2 mm | Can it flex enough for insertion without bowing? |
| Side clearance | At least 3 mm per side | Can the cased phone slide freely? |
| Depth clearance | At least 3 mm | Is the phone easy to remove? |
| Pocket depth | Phone thickness plus no more than 3 mm | Does the phone stay in place when tilted? |
Possible sheet materials include thin plastic or board suitable for craft use. Adhesives and fasteners vary by material, so check product instructions for surface preparation, use, and curing time. Do not assume that an adhesive will bond well to every clipboard finish.
Attach the pocket without creating hazards
Lay out the pocket parts on the backer first. Keep the top open, and make sure the phone’s cameras, buttons, and charging port are not blocked. Use a compatible adhesive or fasteners that do not stick through the clipboard’s writing face.
If you use adhesive, apply it as directed and let it cure for the full time specified by its manufacturer. If you use fasteners, check both sides of the board as you work. A protruding screw, staple, or sharp edge can snag the phone, scratch a hand, or damage the writing surface.
Round exposed corners and smooth rough edges. Remove burrs, which are small sharp ridges left after cutting. Do not seal the pocket or add a lid that makes the phone difficult to see or remove.
Fit, Retention, and Safety Verification
Verification is a final check of fit, clip movement, writing function, and safe use. Test the finished clipboard only after the adhesive has cured or the fasteners are secure. A phone should remain easy to remove, and the pocket should not trap heat or interfere with normal handling.
Test the finished holder
Use this sequence before carrying the clipboard:
- Check that the pocket is firmly attached and has no loose edges.
- Insert and remove the cased phone several times. It should not scrape, bind, or require force.
- Gently tilt the clipboard in different directions. The phone should not slide out or shift excessively.
- Open and close the clip. Confirm the pocket does not touch or block it.
- Place the clipboard on a flat surface and test writing on the front. Check for bumps or wobble.
- Inspect the pocket and board for sharp edges, exposed fasteners, or damage.
If any test fails, remove the phone and adjust the design before use. Do not carry a phone in a pocket that is loose, damaged, or hard to access.
Manage heat and battery risks
A close-fitting pocket can limit airflow around a phone. Heat may also build when a phone is powered on, used heavily, charging, or left in direct sun. Keep the pocket open at the top, do not charge the phone inside it, and remove the phone if it becomes warm.
Never store a hot, damaged, or swollen battery in the pocket. If a phone or battery looks damaged, stop using the holder for that device and follow the device maker’s safety guidance. The clipboard pocket is not a protective case.
Example Setups and Design Choices
These examples are planning scenarios, not reports of tested products. They show how the same measurements and checks can lead to different choices. In each case, the user should confirm local rules first and keep the phone pocket visible and accessible.
Scenario: A slim phone in a study clipboard
A student measures a cased phone and finds that a thin pocket can fit on the back without overlapping the clip. They make a cardboard template, add the required clearances, and test writing on the front. If the school allows phones to be carried, the open pocket can serve as ordinary storage; it should not be used to conceal a phone during a restricted activity.
Scenario: A thicker case in an office
An office worker’s case adds bulk, so a model-based estimate would leave too little room. Measuring the full device reveals the needed pocket size. The worker checks that the added weight does not make the clipboard awkward and keeps the phone out of the pocket when charging or when it feels warm.
Scenario: A clip that uses most of the back
Some clipboards have large rear hardware. A mock-up may show that a pocket would interfere with the clip or make the board uneven. In that case, choose a different location only if it remains practical and safe, or use a separate phone pouch instead.
Conclusion
A well-made clipboard phone pocket depends on accurate measurements, a shallow open design, compatible materials, and careful testing. Start with the cased phone, allow at least 3 mm at the sides and in depth, and keep the pocket depth within 3 mm of the phone’s thickness. Most important, use it only where phone storage is permitted and never treat it as a secure or heat-safe enclosure.
Frequently Asked Questions
How much clearance should a clipboard phone pocket have?
Allow at least 3 mm on each side and 3 mm in depth beyond the phone’s measurements with its case fitted. This gives room for insertion and removal without making the pocket unnecessarily loose.
How deep should the pocket be?
Keep the pocket no deeper than the phone’s thickness plus 3 mm. A deeper pocket may let the phone shift or fall when the clipboard is tilted.
Should I measure my phone with its case on?
Yes. Measure the phone with the case you plan to use, including raised camera edges. A different case may require a new fit check.
Can I seal the pocket or add a flap?
An open top is recommended so the phone stays easy to see and remove. Do not seal the pocket or make it harder to inspect, especially in places with phone rules.
Can I charge a phone inside the pocket?
No. Do not charge a phone while it is enclosed in the pocket. Remove it to charge, and keep it out if it becomes hot.
What materials should I use?
A 3–6 mm rigid backer and a 1–2 mm pocket face are starting points. Check the material and adhesive makers’ instructions, since bonding and cutting needs vary.
How do I stop the phone from falling out?
Use the stated clearances, keep the pocket shallow, and test the clipboard at gentle angles. If the phone slips out, adjust the fit or position rather than sealing the pocket.
Will this work with every clipboard?
No. Clip size, board shape, back surface, and writing-face construction differ. Make a cardboard mock-up and confirm the clip still works and the front remains flat.
Is a DIY pocket secure or fire-rated?
No. Ordinary craft materials and adhesives are not a tested secure container or fire-rated enclosure. Use it only for basic carrying where permitted.
What should I do if the phone feels warm?
Remove it from the pocket and let it cool in a suitable place. Do not store a hot, damaged, or swollen battery in the holder.
(This article was written by one of our staff writers, Samuel Thornton. Visit our Meet the Team page.)






