Hide Blankets in Recliners (Console Storage Arms)
To store a blanket in a recliner console arm, first confirm that the manufacturer allows the space to be used for storage. Measure the folded blanket, then check the full movement path for the seat, lid, wiring, and linkage. Use a removable insert only if it fits without cutting the frame or contacting electrical parts.
A blanket compartment should be easy to open, clean, and inspect. Yet adding storage to an arm can create problems if it blocks moving parts or presses on wiring. I treat the recliner’s manual and service information as the starting point, not the shape of the arm. There is no general building-code size or clearance for a blanket compartment.
Before changing the furniture, identify its exact model and ask the manufacturer about the console structure, permitted storage, and moving-part clearances. If the maker does not approve modification, keep the blanket in an existing, intended storage space instead. That choice is often safer and simpler to maintain.
Planning the Blanket Compartment
A blanket compartment is usable only when it fits the folded blanket and remains within the recliner’s approved storage space. Start with the blanket and the model instructions, rather than estimating from the arm’s exterior. The dimensions below are project allowances for fit, not code requirements or proof that the console can carry extra weight.
Measure the blanket and set a fit allowance
Fold the blanket as you plan to store it. Measure its folded length, width, and thickness, and record each measurement in millimetres or inches. Measure the blanket itself, not its product label: fabric thickness and fold shape can change how it fits.
As a project design allowance, make the compartment’s clear internal length, width, and height at least 25 mm (1 in) greater than the matching blanket dimension. This means 25 mm extra per dimension overall, not 25 mm on every side. For example, a blanket folded to 300 × 250 × 80 mm calls for at least 325 × 275 × 105 mm of clear space. The allowance helps with placement, but the finished fit still needs a hands-on check.
For non-upholstered compartment dimensions, aim for fabrication accuracy within ±3 mm (⅛ in). Upholstery, lining, seams, and padding can reduce the opening, so check the finished clear dimensions before closing the compartment or applying final upholstery.
Confirm that storage is permitted
An arm that looks solid may contain a frame rail, linkage, fastener, wire, power supply, or other component. Do not infer its storage capacity from its appearance. Look for a manufacturer-published storage or load rating. If none is available, do not add a shelf or load-bearing hardware; keep any approved stored contents to one lightweight blanket.
Next step: Measure the folded blanket and ask the manufacturer whether the existing console space can safely be used for storage.
Measuring Access and Recliner Clearances
Clearance means the space a part needs as it moves, not just the gap visible when the recliner is upright. Obtain the model’s service drawing or ask the manufacturer for the full-motion mechanism envelope, meaning the space occupied by moving parts throughout their travel. There is no universal safe gap for all recliners.
Survey the model, mechanism, and wiring
Find the model and serial number, then obtain the owner’s manual and any available service information. Inspect only areas the manufacturer identifies as safe for user access. Note the console lid, hinges, fasteners, visible wiring, power supply, batteries, and linkage. Do not remove upholstery to look inside unless the manufacturer directs you to do so.
A useful survey record includes:
- Recliner model and power type
- Blanket’s folded length, width, and thickness
- Existing console opening’s clear dimensions
- Locations of visible cables, power supplies, hinges, and moving parts
- The manufacturer’s storage, service, and clearance instructions
Do not treat a single upright-position check as proof of clearance. A lid or blanket that appears clear at rest may contact a moving linkage, snag fabric, or pinch a cord as the recliner opens or closes.
Check every position before fitting storage
If the manufacturer permits the proposed insert, make a removable mock-up that represents its final size and lid position. With the recliner unplugged where the manual instructs, check for interference through the full travel path. Then follow the manufacturer’s operating and testing instructions; do not put hands near moving parts while the mechanism is powered or moving.
A nominal gap does not replace the model-specific motion envelope. If any part touches the mock-up, lid, blanket, or cable, stop. Do not trim a moving component or shift wiring to make the space fit.
| Check | What to measure or observe | Stop if |
|---|---|---|
| Blanket fit | Folded length, width, and thickness | Blanket must be forced into place |
| Clear compartment | Finished inside dimensions | Lining or padding reduces the needed opening |
| Motion envelope | Full travel, using model-specific guidance | Linkage, lid, or blanket contacts a part |
| Electrical items | Cable and power-supply locations | A cable is pinched, trapped, or covered |
| Storage load | Published manufacturer rating | No rating exists and added support is needed |
Next step: Do not build around guessed clearance. Get the maker’s guidance, then test the proposed shape across the full range of motion.
Building and Finishing the Storage Insert
A storage insert is a removable liner or container that uses existing approved space without changing the recliner’s frame. It should not carry loads beyond the manufacturer’s stated limit, obstruct the mechanism, or put pressure on wiring. If a safe fit depends on cutting, drilling, or stapling into the console, stop and seek written manufacturer approval.
Build conservatively and protect the upholstery
Use the existing console volume only if the manufacturer allows it. Keep the insert removable so you can inspect and clean the space. Do not cut, drill, staple, or drive fasteners into the frame or console without approval; concealed linkage and wiring can be damaged, and the structure’s capacity may be unknown.
Round or pad exposed edges so they do not snag the blanket or rub the upholstery. Make sure the insert does not press on the arm walls or force the lid shut. A blanket should lift out without catching on a hinge, seam, or sharp edge.
The lid should stay closed during normal use, but it must not be secured in a way that changes the recliner mechanism or creates a pinch point. Use only a closure method approved by the manufacturer. Do not add a latch or hinge that requires drilling into an unverified area.
Keep electrical components clear
Do not relocate, pinch, splice, or enclose recliner wiring, power supplies, or batteries. Do not route an extension cord through the compartment, cover a vent, or store a blanket against a warm electrical component. Follow all manufacturer-specified ventilation and heat clearances; there is no general blanket-storage airflow rule.
Where listed electrical equipment is involved, NEC 110.3(B) requires installation and use consistent with its listing and labeling. The applicable code edition and local adoption depend on the jurisdiction. This is not permission to alter the recliner’s electrical system. For an electrical concern, contact the manufacturer or a qualified service provider.
Next step: Use a non-load-bearing, removable insert only when the manufacturer permits it and the compartment stays clear of all electrical and moving parts.
Verifying Motion, Retention, and Electrical Safety
Verification means checking the finished storage arrangement under the conditions it will face in use. Test with the blanket inside, not just with an empty cavity. Inspect the compartment, lid, upholstery, and visible cables before and after full-motion cycles, following the manufacturer’s instructions.
Test the loaded compartment
Place one lightweight blanket in the approved compartment. Confirm it is not compressed against a cable, hinge, power supply, vent, or moving part. Close the lid without forcing it, then operate the recliner according to the manual. Keep clear of the mechanism during movement.
Stop and remove the insert if you notice contact, pinching, snagging, unusual resistance, fabric abrasion, cable movement, or heat near the blanket. Do not continue cycling the chair to “wear in” a tight fit. Contact the manufacturer or an authorized service provider if you cannot confirm safe clearance.
After the initial test, inspect again for rubbed fabric, shifted wiring, loose fasteners, or a lid that has moved. Repeat the inspection after cleaning or changing the blanket fold, since either can affect the fit. A compartment that clears when upright may still trap a blanket or pinch a cord during motion.
Practical assessment examples
These examples show how to apply the measurement method; they are not reports of specific customer installations or proof that any recliner can be modified.
- Compact throw: A throw folded to 300 × 250 × 80 mm needs at least 325 × 275 × 105 mm of clear internal space under the stated project allowance. If the console is smaller, do not compress the blanket to force a fit.
- Power recliner with a cable nearby: If the blanket or insert could touch the cable during movement, the proposed space is unsuitable. Do not reroute the cable or cover the power supply; ask the manufacturer about an approved storage location.
- Unrated arm structure: If the manufacturer provides no storage or load rating, do not install a shelf or add support hardware. Keep to a single lightweight blanket only if the maker confirms that using the existing cavity is acceptable.
Next step: Complete a loaded, full-motion test and stop at the first sign of contact, pinching, snagging, or heat.
Conclusion and FAQ
Safe blanket storage depends on the exact recliner model, not a universal compartment size. Measure the folded blanket, confirm that storage is allowed, and preserve the full mechanism and electrical clearances. A removable insert may work in an approved existing space; cutting or fastening into the recliner without manufacturer approval is not a safe shortcut.
Can I store a blanket in any recliner console arm?
No. Check the recliner’s manual or ask the manufacturer whether the console is intended for storage. Some spaces may contain wiring, power supplies, or moving parts, even when those parts are not visible.
How much extra space should I allow?
As a project fit allowance, add 25 mm (1 in) to each folded blanket dimension: length, width, and thickness. This is not a code minimum or a universal recliner specification.
Is there a standard clearance from the recline mechanism?
No. Use the manufacturer’s service drawing or ask for the model’s full-motion mechanism envelope. A clearance that looks adequate in the upright position may not remain clear during movement.
Can I cut into the arm to make room?
Do not cut, drill, or staple into the arm or console without manufacturer approval. Hidden rails, linkage, wiring, and fasteners may be damaged, and the structure’s load capacity may be unknown.
How much weight can a console arm hold?
Use only a manufacturer-published storage or load rating. Do not estimate capacity from the arm’s appearance. If no rating is available, do not add a shelf or load-bearing hardware.
Can I store a blanket beside a power supply?
Only if the manufacturer’s instructions allow it and required heat and ventilation clearances remain open. Do not cover a power supply, vent, battery, or cable with a blanket.
Should I test the recliner with the blanket inside?
Yes, if the manufacturer permits storage. Check the entire travel path with the compartment loaded, following the manual. Stop if the blanket, insert, lid, or wiring contacts or catches on anything.
Can I use an extension cord in the compartment?
No. Do not route an extension cord through the cavity, pinch or splice recliner wiring, or enclose electrical components. Follow the recliner’s instructions and contact the manufacturer about power concerns.
(This article was written by one of our staff writers, Andrew Fairchild. Visit our Meet the Team page.)






