Hide Cash in Pallet Nightstand (Woodworking Plans)
Build a pallet-style nightstand with a small, nonstructural compartment beneath its top. Use only clean, dry boards, and measure each piece after dismantling. A 12 × 8 × 1½-inch (305 × 203 × 38 mm) cavity is a useful starting point, not a fixed rule. Support its access panel on solid cleats, then test the fit and finish.
A common mistake is to cut a cavity into a leg or rail because it seems like the quickest way to hide cash. That can weaken the nightstand and leave a panel that binds or sags. Instead, build the hidden space as a separate box beneath the top, away from load-bearing parts.
The plan below uses a removable inset panel supported by cleats. It suits a nightstand about 18 inches wide, 16 inches deep, and 24 inches high, but you can scale it to your room and materials. A concealed compartment can reduce casual visibility, but it is not a safe, fireproof box, or guarantee against theft.
Plan the Nightstand and Inspect Pallet Lumber
Start by checking the room, nightstand footprint, and lumber before drawing the cut list. Pallet boards vary in width, thickness, and condition, so do not base a precise plan on assumed dimensions. A plywood liner or consistent ¾-inch (19 mm) stock makes the carcass easier to square and the compartment easier to fit.
Measure the space beside the bed, including the gap to the wall and mattress. Confirm that a drawer, if included, can open without hitting either. Decide whether the concealed panel will lift out from the top or swing open; the removable panel in this plan needs less hardware and avoids a hinge line.
Sort and prepare the boards
Pallets may have held unknown goods or been exposed to spills. Reject boards with mold, oily residue, chemical odors, or other signs of contamination. An “HT” mark indicates heat treatment for pest control; it does not prove the wood is clean or suitable for indoor furniture.
Dismantle the pallet with eye protection. Work slowly to reduce splits, and remove nails, staples, and metal fragments before cutting or planing. Measure every board after dismantling. If the boards are too thin or uneven for a stable carcass, use them as visible trim over a plywood or solid-wood frame.
A practical sample design is 18 inches wide, 16 inches deep, and 24 inches high. These are outside dimensions, not a standard. Keep the compartment near 12 × 8 × 1½ inches, adjusting it to the actual top and the cash or small items you plan to store.
Set Compartment Access and Furniture Clearances
The hidden space should fit beneath the top without cutting into legs, rails, or other supports. A removable inset panel sits on cleats above a shallow box; the panel’s edges follow the surrounding top boards. Plan its opening and seam before assembly, because wall or mattress interference can make access awkward.
For the sample 18 × 16-inch top, a 12 × 8-inch panel leaves a border around the opening. Center it only if that leaves enough room for the legs, rails, and any drawer below. A roughly 1½-inch-deep box gives a low-profile cavity; confirm the finished depth after accounting for the top, cleats, and panel thickness.
| Choice | Useful when | Main trade-off |
|---|---|---|
| Removable inset panel on cleats | You want simple access and few moving parts | It needs a discreet way to lift it |
| Hinged inset panel | You need the panel attached to the nightstand | Hinges require secure mounting and can reveal a seam |
| False back inside the carcass | The top cannot accommodate an inset | It reduces usable interior space |
Leave about ⅛ inch (3 mm) clearance around a removable or sliding panel. Reclaimed wood can shift with humidity, so treat this as a starting point, not a guarantee. Dry-fit the panel in the assembled opening and adjust it until it lifts without binding.
Do not rely on friction alone to retain the panel. If you use a catch or other hardware, choose one with a published rating and follow its installation instructions. Support the panel on cleats so the catch retains it rather than carrying the weight of objects placed on top.
Build the Carcass, Compartment, and Concealed Panel
Build a square, stable nightstand first, then add the compartment as a separate, non-load-bearing box beneath the top. This order keeps the hidden feature from weakening the frame. For consistent parts, use ¾-inch stock or plywood for the carcass, with pallet boards added as facing or trim.
Make the frame and compartment
Cut and label parts only after confirming their final widths and thicknesses. For an 18 × 16-inch outside footprint, account for the actual thickness of the legs, rails, and panels when sizing each piece. Pallet boards are rarely uniform, so a fixed cut list can mislead; make a measured drawing that shows how each joint changes the finished size.
- Build the carcass. Join the legs, side rails, and back using sound furniture joinery suitable for your stock. Keep the top rails level and square. Add a lower shelf or drawer only if it does not interfere with the compartment.
- Check the frame. Measure diagonals to spot a rack or twist, then correct it before the joints set. Set the frame on a flat surface and check for rocking.
- Make the compartment box. Assemble a shallow box to the target inside dimensions. Keep it independent of the legs and rails, and fasten it beneath the top with suitable screws or joinery into solid wood.
- Fit support cleats. Install cleats around the opening so the panel rests on them. Attach cleats to solid material, not to a thin pallet slat alone. The panel should sit level with the surrounding top.
- Cut and fit the panel. Match its grain and board direction to the top where practical. Leave about ⅛ inch around its edges, then test the fit with the nightstand assembled.
Make the seam less noticeable
A concealed panel is easiest to spot when its grain, color, or gap differs from the top. I align the panel’s grain with nearby boards and keep the gap even rather than trying to make it disappear. A consistent seam looks more like a planned joint and is less likely to bind.
Use a discreet lift point or a catch designed for the panel. Do not make a deep notch that weakens a narrow edge. If you choose a catch, mount it as directed and verify that it holds the panel in place without pulling the cleats loose. Avoid placing stored items where they can press against the panel from below.
Verify Fit, Stability, and Finish
Before finishing, check the nightstand as furniture and the concealed feature as a moving part. The top must remain supported by the frame, while the compartment stays clear of structural rails. Test the panel repeatedly, then inspect the joints, edges, and hardware for looseness, binding, or pinch points.
One useful build scenario is a narrow bedside table with an 18 × 16-inch top and limited room beside the bed. A centered inset panel may be hard to lift near a wall, so shift it toward the room-facing side while keeping it supported on all four cleats. A second scenario is a table with a drawer directly below the top: reduce the box depth or move it back so it does not block the drawer. These are layout checks, not claims about a tested product; measure your own furniture before cutting.
| Check | Pass condition | If it fails |
|---|---|---|
| Panel clearance | Panel lifts freely with a steady gap near ⅛ inch | Trim or sand the edge; recheck the gap |
| Cleat support | Panel rests flat on solid, secure cleats | Reposition or reinforce the cleats |
| Frame stability | No rocking on a flat floor | Square and repair the frame before use |
| Hardware | Fastened to solid wood and used within its published rating | Re-mount or select suitable rated hardware |
| Drawer and room access | Panel and drawer clear the wall, bed, and each other | Change the opening position or compartment depth |
Sand splinter-prone edges and remove dust before applying an indoor-use finish. Follow the finish label for application, ventilation, and cure time; do not load the compartment or use the nightstand until the finish has fully cured as directed. After curing, test the panel again, since finish can change a close fit.
No building-code provision specifically governs a concealed furniture compartment. Still, follow the lumber, finish, and hardware manufacturers’ requirements. A pallet’s former load rating does not transfer to your nightstand. If the table rocks or a joint opens under ordinary hand pressure, repair it before use. The main takeaway is simple: keep the cavity out of load-bearing members and make the panel rest on sound supports.
Frequently Asked Questions
These short answers cover common choices when planning a pallet-wood nightstand with a hidden cash space. Use them to check your design, but base final dimensions on the measured furniture and the actual boards. The panel, supports, and hardware must work together; no single measurement suits every build.
How big should the hidden compartment be?
A practical starting size is 12 × 8 × 1½ inches (305 × 203 × 38 mm). Adjust it to the nightstand’s dimensions and the items you intend to store.
Is pallet wood marked HT safe for indoor furniture?
The HT mark means the pallet was heat-treated for pest control. It does not confirm that the wood is free from spills or other contamination. Reject questionable boards.
Can I cut the compartment into a leg?
No. Keep the cavity out of legs, rails, and other load-bearing parts. Build it as a separate box beneath the top.
How much clearance should the panel have?
Start with about ⅛ inch (3 mm) around a removable panel. Dry-fit it and adjust for the actual wood and humidity-related movement.
Should I use a hinge or a removable panel?
A removable panel on cleats uses fewer moving parts. A hinge can keep the panel attached, but it needs secure mounting and may make the seam easier to see.
Can I rely on a tight fit to hold the panel?
No. Friction alone may not retain it consistently. Use suitable hardware, follow its instructions, and let the cleats support the panel.
Does the pallet’s load rating apply to the nightstand?
No. The pallet’s former rating does not rate your furniture or its joints. Build and test the nightstand as a separate piece.
Will a concealed compartment protect cash from fire or theft?
No. Concealment is not the same as fire protection or theft resistance. Do not treat this furniture feature as a rated safe.
(This article was written by one of our staff writers, Nathaniel Pierce. Visit our Meet the Team page.)




