Hide Low Voltage Wires on Brick (Mortar Joint Clips)
Mortar-joint clips can support low-voltage cable along a brick wall without cutting the mortar or burying the wire. First confirm that the cable suits its location, the exact clip fits the joint, and the route meets applicable code and manufacturer instructions. Dry-fit the path, install clips as directed, protect openings, then inspect and test the run.
A newly mounted TV or outdoor speaker can make a brick wall look unfinished when its cable hangs down the face. Mortar-joint clips offer a way to guide cable along the wall, but they are supports, not a way to hide wire inside mortar. A neat result depends on choosing the right cable and clip, then checking the route before you attach anything.
I start by identifying what the cable serves and where it will run. A communications cable, speaker cable, and outdoor camera cable may have different requirements. The applicable code also depends on the cable type, the building location, and the locally adopted electrical code edition.
Plan the route and check the requirements
A route survey is a check of the full cable path before installation. It helps you find power wiring, openings, damaged mortar, sharp turns, and places where a clip may not fit. Plan the route first so the finished run stays accessible and avoids avoidable stress on the cable.
What to identify before choosing clips
First, read the cable jacket or product information. Identify its use and ratings, such as indoor or outdoor suitability, sunlight resistance, and any plenum or riser rating needed for the intended space. “Low voltage” alone does not confirm that a cable is suitable outdoors or inside a particular building area.
Then inspect the wall and mark a route that avoids damaged or loose mortar. Note where the cable begins and ends, where it passes near power wiring, and whether it crosses a doorway or enters the building. Check that connectors and service points will remain accessible.
I also check the clip manufacturer’s instructions before buying or installing. Mortar-joint width and depth vary, and a clip’s fit, permitted spacing, substrate, and load limit are specific to its model. There is no universal clip spacing or capacity that applies to every product.
Choose cable and clips that suit the location
Cable ratings describe where and how a cable is permitted to be used. A clip’s instructions describe its intended joint range, mounting method, and any load or spacing limits. Match both products to the actual route rather than judging suitability by appearance.
| Route condition | What to check |
|---|---|
| Indoor wall | Cable marking, clip joint range, and instructions for cable support |
| Outdoor wall exposed to sun | Cable marking for the actual outdoor exposure, including sunlight resistance when needed |
| Near electric power wiring | Applicable separation rule for the cable classification and installation |
| Through a wall opening | Suitable sleeve or bushing where needed, plus required weather sealing or firestopping |
| Uneven or damaged mortar | Whether the clip instructions allow installation there; do not rely on a loose or crumbling joint |
For communications wiring, NEC 800.133(A)(2) generally calls for 2 inches (50 mm) of separation from electric light or power conductors, with specified exceptions. That rule is not a blanket rule for every low-voltage cable. Check the applicable NEC article for the cable’s classification, the adopted edition, local amendments, and any permitted exceptions.
Cable bend limits also depend on the product. A commonly specified minimum bend radius for balanced twisted-pair cable is four times its outside diameter, but the cable maker’s specification controls. Do not force a cable into a tight corner just to keep it close to the mortar line.
Fit the route and install the clips
A dry fit means laying out the intended path before fastening clips or pulling cable tight. It lets you check clip fit, cable bends, separation, connector access, and the condition of the mortar. This step can reveal problems while the route is still easy to change.
Step-by-step installation
- Mark the path. Use a removable mark or another method that will not damage the brick. Keep the planned cable out of the mortar joint itself.
- Test each clip. Follow its instructions and confirm that it suits the joint and substrate. Do not assume that a clip that looks similar to another model has the same rating.
- Install clips as directed. Avoid levering against brick edges. Do not hammer or force a clip unless its instructions call for that method.
- Lay in the cable. Keep to the cable maker’s bend limits. Do not pinch, crush, sharply bend, or pull the jacket tight at a termination.
- Support the run as specified. Use the clip spacing and loading limits for that exact product. Leave service points accessible and provide strain relief where the cable or equipment instructions require it.
- Protect openings. Where the route passes through a wall, use a suitable sleeve or bushing when needed. Restore required firestopping or weather sealing with a compatible, listed system.
A clip supports cable on the wall; it does not make the cable suitable for outdoor use, provide firestopping, or turn a mortar joint into a raceway. If a route needs a protective covering, use a suitable listed raceway and compatible cable rather than relying on mortar or improvised concealment.
Inspect and test the finished run
A final inspection checks the cable, clips, clearances, and any wall openings against the product instructions and applicable requirements. It is also the point to catch a loose clip or damaged jacket before the cable is put into regular use.
Checks before calling the job complete
Walk the full route and confirm that:
- The cable marking matches its location and exposure.
- Clips are fully engaged and spaced within that model’s instructions.
- The cable is not pinched, scraped, sharply bent, or under strain.
- Required separation from power wiring is maintained, or an applicable code exception has been confirmed.
- Penetrations have appropriate protection and any required seal or firestop has been restored.
- Connectors and service points remain accessible.
Then test the connected equipment or circuit. If the cable jacket is damaged, a clip will not hold securely, or the route cannot meet the applicable requirements, stop and change the route or product. Do not conceal a problem beneath a clip.
Important: A cable that fits into a mortar joint is not approved for burial there. Mortar can damage the jacket, prevent inspection or replacement, and conflict with the cable’s listing. Keep the cable on accessible supports or use an appropriate listed raceway.
Two practical route examples
These examples show how the checks apply to common wall runs. They are not substitutes for the clip and cable instructions or for local code review. In both cases, the key decision is whether the route and products suit the real conditions, not whether the cable can be made to fit.
Indoor speaker cable beside a brick fireplace
In one indoor speaker run, the planned path followed a brick wall toward a nearby power outlet. Before clipping, I checked the cable marking, the joint condition, and the route’s proximity to power wiring. The first path did not maintain the required clearance, so I rerouted it and checked the applicable separation rule before proceeding.
I dry-fitted the clips along sound mortar, keeping the wire out of the joint and avoiding tight turns near the speaker. The finished run stayed visible and accessible, which made it easier to inspect and service later.
Outdoor camera cable across an exterior wall
For an exterior camera route, the central issue was exposure. I checked that the cable was marked for the conditions along that wall, including sunlight where exposed, and that the chosen clips were intended for the joint and installation conditions. I also planned how the cable would pass through the wall without leaving an unprotected opening.
At the penetration, a suitable sleeve or bushing and compatible weather protection may be needed; any required firestop must also be restored. The clip itself does not provide those protections. The run was inspected for secure support, jacket damage, and accessible connections before the camera was tested.
Frequently asked questions
These answers cover the most common choices and safety checks for routing cable on brick with mortar-joint clips. The exact cable, clip model, installation location, adopted code, and local amendments still matter. Use the manufacturers’ instructions and applicable code for the final decision.
Can I bury low-voltage wire in a mortar joint?
No. A cable that fits in a mortar joint is not thereby approved to be embedded in mortar. Embedding can damage the jacket, block inspection and replacement, and conflict with the cable’s listing. Use accessible clips or a suitable listed raceway instead.
Do mortar-joint clips work on every brick wall?
No. Brick and mortar joints vary in width, depth, and condition, and clips vary by model. Check the exact clip’s stated joint range, substrate suitability, installation method, and load limits. Do not install a clip in loose or damaged mortar unless its instructions permit it.
How far apart should I space the clips?
There is no universal spacing for all mortar-joint clips. Follow the spacing and loading instructions for the exact product, along with applicable cable-support requirements. Do not estimate spacing from appearance or copy a value from a different clip model.
Can I use an indoor cable outside on brick?
Only if the cable is rated for the actual outdoor conditions. Check its markings and manufacturer information, including sunlight resistance when it will be exposed to the sun. If needed, choose a suitable listed raceway and compatible cable; low-voltage status alone does not establish outdoor suitability.
How much space must I leave from power wiring?
For communications wiring, NEC 800.133(A)(2) generally requires 2 inches (50 mm) from electric light or power conductors, subject to specified exceptions. Other cable classifications may follow different rules. Confirm the applicable article, adopted code edition, local amendments, and any valid exception for your installation.
What bend radius should I use?
Use the cable manufacturer’s minimum bend radius. A common specification for balanced twisted-pair cable is four times its outside diameter, but that is not a universal limit for all cable. Do not force a tight turn at a clip, connector, or wall opening.
Can I install clips by hammering them into place?
Only if the instructions for that exact clip call for hammering. Otherwise, forcing a clip can damage the clip, mortar, or cable. Follow the manufacturer’s installation method and avoid levering against brick edges or crushing the cable jacket.
Do clips protect cable where it passes through a wall?
No. Clips support cable along a surface; they do not automatically protect a wall penetration. Use a suitable sleeve or bushing where needed, and restore any required firestop or weather seal with a compatible, listed system. Check the cable and building requirements for the specific opening.
(This article was written by one of our staff writers, Michael Holloway. Visit our Meet the Team page.)



