Hide Samsung Frame Wires (In-Wall Power Box)

To hide a Samsung Frame TV’s power connection, use a listed in-wall power-relocation kit or have an electrician install a permanent recessed receptacle behind the TV. Never bury the supplied power cord or an ordinary extension cord. Route the One Connect cable inside the wall only after confirming that the exact cable and TV instructions permit it.

A common misconception is that a cable becomes safe to hide once it is behind drywall. It does not. The TV’s flexible power cord and the One Connect cable are different products, and each has its own rules for where it may run.

I plan these installations around the exact Frame model, cable version, wall construction, and local code. That matters because a recessed power box can be installed correctly while an unapproved signal cable still creates a problem. Here is how to choose a safe route and check the work.

Plan the model, cable route, and code path

Start by identifying the exact TV model and One Connect cable before buying a kit or opening the wall. Samsung instructions vary by model and cable version, and local rules can vary by location. Treat the TV manual, kit listing and instructions, adopted electrical code, and local amendments as the controlling documents.

Find the model number on the TV or its documentation, then locate the matching Samsung installation instructions. Check the markings on the One Connect cable and look for explicit permission for in-wall use in the matching manual. A cable that looks like a low-voltage signal cable is not automatically suitable for concealment.

Next, map the wall. Locate studs, existing outlets, and known plumbing or wiring, and decide where the TV receptacle and One Connect box will sit. Check permit requirements with your local building department before electrical work; do not assume that a particular kit or installation is exempt.

The supplied TV power cord is a flexible cord. NEC 400.12 generally prohibits concealing flexible cords in walls, so do not run that cord through a hole and cover it with drywall. An ordinary extension cord is not a substitute for permanent wiring.

  • Next step: Confirm the model, cable, wall route, instructions, and permit requirements before cutting.

Check recessed-box, mount, and ventilation clearances

A recessed box must fit the wall and the TV setup without being crushed, blocked, or made inaccessible. Check its depth and position against the mount, studs, and other services. Also plan how the One Connect cable will bend and where the One Connect box will sit so its ventilation openings stay clear.

Dry-fit the planned locations using the kit’s dimensions and the TV’s mounting layout. A box that physically fits in a stud bay may still conflict with the mount or leave too little room for the cable connector. Do not force a tight bend or pinch a cable behind the TV.

There is no single clearance or airflow figure that applies to every Frame and One Connect setup. Follow the exact Samsung and kit instructions. Keep the One Connect box accessible as instructed, and do not seal it in an unventilated wall cavity or enclosure.

Clearance checkWhat to confirm
Recessed power boxIt fits the wall and does not collide with the mount, studs, or other services.
Low-voltage openingIt allows the approved cable and connector to pass without pinching.
One Connect cableThe route respects the cable’s stated bend and handling limits.
One Connect boxVentilation openings remain unobstructed, and the box is placed as instructed.

If the proposed positions do not work together, adjust the layout before making openings. Do not solve a clearance issue by crushing the cable, removing a required box, or burying the One Connect box.

Choose a listed power and signal pathway

A power-relocation kit is a listed assembly designed to bring power from an existing receptacle to a new receptacle location. A permanent receptacle is a fixed outlet wired as part of the home’s electrical system. Either approach can hide the TV’s power connection when installed according to its instructions and local requirements.

ApproachPower connectionWhen it may fitMain check
Listed in-wall power-relocation kitMoves power to a recessed receptacleThe kit suits the wall and the installation follows its listingUse every required part and follow its instructions
Electrician-installed permanent receptacleAdds a fixed, recessed outletThe wiring route and location are suitable for permanent wiringConfirm permits, box fill, wiring method, and local code
Supplied power cord through drywallHides a flexible cordNot an appropriate in-wall power methodDo not conceal it
One Connect cable in-wallCarries the TV’s signal and connectionOnly if the exact cable and model instructions allow itVerify the cable’s markings and matching Samsung manual

A kit’s listing does not make every installation acceptable. Its instructions still govern, and the local authority may require permits or other steps. If the kit does not fit the wall or its instructions do not cover the planned setup, ask an electrician to assess a permanent receptacle instead.

For the signal path, use only a One Connect cable explicitly permitted for the concealed location. If its markings or the matching Samsung documentation do not establish that, keep it outside the wall or ask Samsung or a qualified installer to confirm. Never cut or splice the cable.

Install the approved pathways and check electrical details

If you are not qualified to do electrical work, hire a licensed electrician. Electrical box sizing, wiring methods, and permit rules are not guesswork. A listed kit can simplify the installation, but it does not remove the need to follow its instructions and the locally adopted code.

Before work begins, verify the planned openings and route again. Keep mains wiring and low-voltage wiring separated, or use a partitioned arrangement, as required by the applicable code and equipment listing. Do not place the power path and signal cable together simply because both lead to the TV.

Two code details deserve attention:

  • Conductor length: NEC 300.14 generally requires at least 6 inches (152 mm) of free conductor at each outlet, junction, and switch point, measured from where it emerges from the raceway or cable sheath. Where the box opening is less than 8 inches (203 mm) in any dimension, at least 3 inches (76 mm) must extend outside the opening.
  • Box fill: NEC 314.16 sets how much conductor and device volume an electrical box must hold. The box must be sized for the items inside; a recessed box is not adequate just because it fits in the wall.

The electrician or installer should secure the boxes and cables as required, preserve conductor length, and close the wall only after the wiring and cable route have been checked. Do not improvise a splice, omit a listed component, or cover a box that must remain accessible.

Verify box fill, cable suitability, and operation

Before finishing the wall, check that the electrical box is the right size for its conductors and devices, and that the installation preserves the required conductor length. Confirm the One Connect cable is approved for its route, undamaged, and free from tight bends. Then test the receptacle and the TV connection.

A careful final check can prevent a clean-looking finish from hiding a wiring or ventilation problem. I look at the cable path, box position, and One Connect placement before the TV goes onto the mount. If any instruction is unclear, stop and confirm it rather than guessing.

  • Confirm the power connection is a permanent receptacle or part of a listed relocation kit, not a buried flexible cord.
  • Confirm the One Connect cable is approved for in-wall use for that exact setup.
  • Check that connectors are not pinched and cable bend limits are respected.
  • Keep the One Connect box ventilated and placed as instructed.
  • Test the receptacle and confirm the TV and One Connect system operate normally.

If the cable is unmarked or the manual does not clearly permit in-wall routing, do not conceal it. A safe power solution does not make an unverified signal cable safe to bury.

Two installation scenarios to guide your plan

These examples are illustrative planning scenarios, not claims about a specific home or Samsung model. They show how I would apply the same checks to different wall conditions. In both cases, the exact model instructions, kit directions, and local requirements take priority.

Scenario 1: The mount leaves room for a listed kit. The owner identifies the TV and One Connect cable, confirms the kit is suitable for the wall, and checks that the recessed box will not conflict with the mount. The cable markings and matching Samsung instructions allow the chosen signal route. The kit is installed as directed, and the One Connect box remains ventilated and accessible as instructed.

Scenario 2: The cable rating is unclear. The power kit appears to fit, but the One Connect cable has no clear in-wall approval in the available documentation. The right choice is not to assume it is safe because it is low voltage. Keep that cable outside the wall while confirming the exact cable guidance, or use another approved arrangement.

These examples highlight the key decision: verify each pathway separately. The power route and signal route do not share one blanket approval.

Conclusion and FAQ

A clean Frame TV installation starts with two separate checks: use an approved method for the power connection, and verify the exact One Connect cable before placing it inside a wall. Recessed boxes also need proper clearance, adequate box fill, and installation that follows the kit instructions and local rules.

I would not close the wall until those checks are complete. If the model, cable, or code path is uncertain, ask a qualified electrician or Samsung to confirm the requirements for that setup.

Can I hide the Samsung Frame TV’s supplied power cord in the wall?
No. NEC 400.12 generally prohibits concealing flexible cords in walls. Use a listed in-wall power-relocation kit or a properly installed permanent receptacle.

Can I use an ordinary extension cord behind the drywall?
No. Do not conceal an ordinary extension cord in a wall. Use an approved permanent wiring method instead.

Can every One Connect cable go inside the wall?
No. Check the markings and the Samsung instructions for the exact TV and cable. Low voltage alone does not prove that a cable is approved for concealed use.

Does a listed power kit mean I can skip local requirements?
No. Follow the kit instructions and the adopted local code. Permit rules and local amendments may also apply.

Can I put the One Connect box inside the wall?
Do not seal it in an unventilated cavity. Follow the exact Samsung instructions for its placement, access, and ventilation.

How much free conductor does NEC 300.14 require?
Generally, at least 6 inches (152 mm) at an outlet, junction, or switch point. For a box opening smaller than 8 inches in any dimension, at least 3 inches (76 mm) must extend outside the opening.

How do I know if the recessed electrical box is large enough?
Its volume must meet NEC 314.16 requirements for the conductors and devices inside. Have the box fill checked rather than relying on whether it physically fits.

What if I cannot confirm the One Connect cable’s rating?
Do not conceal it in the wall. Keep it outside the wall until Samsung or a qualified installer confirms the correct guidance.

Should I hire an electrician?
Hire one if you are unsure about permanent wiring, box fill, permits, or local code. A listed kit still has to be installed correctly.

Can I cut or splice the One Connect cable to make it fit?
No. Do not cut or splice it. Use the cable and route as instructed for the exact system.

(This article was written by one of our staff writers, Michael Holloway. Visit our Meet the Team page.)

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *