Hide Shoes in Ikea Trones Shoe Cabinets (Slim Racks)
IKEA TRONES cabinets can hide everyday shoes in a narrow space, but a safe, useful setup starts with the wall and the available clearance. Measure the cabinet, check the mounting surface and nearby doors, then follow the instructions for your exact model. Secure every required fixing, keep shoes dry, and leave the cabinet easy to open and use.
If shoes spill into your entryway, a slim cabinet can help reduce the visual clutter without taking up much floor space. One TRONES cabinet is nominally 20½ inches wide, 7⅛ inches deep, and 15⅜ inches high (52 × 18 × 39 cm). IKEA sells it as a two-cabinet package, but confirm the model and dimensions in your market before planning.
Its shallow profile is useful, but it does not make every wall or hallway suitable. Below, I’ll walk through the checks that matter: where the cabinet can go, how to preserve access and passage space, and how to install and inspect it without guessing about the wall or fasteners.
Planning the TRONES Layout and Wall Substrate
A wall substrate is the material behind the cabinet, such as wood framing, masonry, or drywall. It determines which fasteners are suitable. Before marking a layout, confirm the exact TRONES model, read its assembly instructions, and identify the wall material so you can plan a secure, accessible location.
Measure the wall and find conflicts
The cabinet’s nominal depth is 7⅛ inches, but the finished setup must also allow the front to open and shoes to be removed. Use the exact product instructions for the mounting points and check the space around the cabinet before drilling.
Start with these checks:
- Measure the wall section and mark the cabinet footprint.
- Check for baseboards, trim, nearby handles, and door swings that could interfere.
- Look for likely wiring or plumbing routes before drilling. If you cannot tell what is behind the wall, pause and seek qualified help.
- Decide how many cabinets fit without blocking other fixtures or circulation.
The pair in the package does not mean every installation should use both units in one stack. Lay out each cabinet separately and check the full arrangement against the instructions.
Identify the wall before choosing fasteners
Fasteners are screws or anchors that secure the cabinet to the wall. Their suitability depends on the actual wall and the load. IKEA requires the cabinet to be attached to a wall, but there is no single anchor type or load rating that can be recommended for every wall and shoe load.
Use the fixing method specified for your wall construction. Do not rely on adhesive, drywall alone, or a fastener’s advertised capacity without checking that it suits the substrate and installation. If you are unsure whether a fixing point reaches framing or a suitable anchor, stop and verify rather than improvising.
Checking Door Swing, Passage Width, and Access
A cabinet is only useful if its front can open and your shoes remain easy to reach. Check the space with the cabinet in its planned position, not just the wall dimensions. In a hallway, measure the narrowest finished passage after installation and compare it with the rules that apply locally.
Check the finished hallway width
IRC §R311.6 requires hallways to be at least 36 inches (914 mm) wide where that provision is adopted and applies. Local rules can differ, so check the code adopted in your area. Measure the remaining clear width at the narrowest point, with the cabinet installed, rather than relying on the original wall-to-wall measurement.
A cabinet that projects into a hall can reduce that clear width. Also check whether an open front or a person using the cabinet would block the route. If the cabinet leaves too little space, choose another location instead of assuming its slim profile makes the placement acceptable.
Dry-fit the arrangement before drilling
A dry fit means holding or positioning parts in place to check how they work before making permanent holes. Mark the cabinet outline and fixing points from the instructions. Then test the planned position against doors, adjacent cabinets, and the route people use.
| Check | What to measure or test | What to do if it fails |
|---|---|---|
| Cabinet footprint | Width, height, and 7⅛-inch nominal depth | Recheck the exact model and available wall space |
| Front access | Open the cabinet and remove a typical shoe | Move it if the front hits a door or fixture |
| Hall clearance | Narrowest finished passage | Check local requirements; choose another location if needed |
| Wall fixing | Substrate and instructed fixing points | Confirm a suitable method before drilling |
A paper outline can help you see the cabinet’s footprint, but it cannot test how the front moves. Use the actual cabinet, or a safe, temporary stand-in, for the final access check. Keep the planned arrangement clear of the path through the home.
Securing the Cabinets and Finishing the Surround
Install the cabinet only after confirming its position, wall material, and fixing method. Follow the current IKEA assembly instructions for the exact product and install every required fixing. Do not modify the cabinet or close it into a surround that blocks opening, removal, or ventilation.
Follow the instructions for the exact model
IKEA lists polypropylene plastic as the cabinet material. Product details and instructions can vary by model or market, so use the information supplied for the cabinet you have rather than assuming another version is identical.
A careful installation sequence is:
- Confirm the wall material and check for hidden wiring or plumbing.
- Mark the footprint and fixing points as shown in the instructions.
- Use fasteners suited to the actual substrate and specified installation.
- Attach the cabinet using every required fixing.
- Fit any adjoining cabinet as instructed, then check that each front opens freely.
There is no universal anchor recommendation here. Wall type, fastener choice, cabinet arrangement, and shoe load all matter. If the instructions do not cover your wall or you cannot confirm a secure fixing method, ask a qualified installer.
Keep trim nonstructural and removable
A neat surround can make a row of cabinets look built in, but trim should not carry the cabinet or block its operation. Do not seal the unit into a permanent enclosure. Leave room to open it and access the fixings if the cabinet needs to be removed.
Before adding trim, test the cabinet through its full opening motion. Check that trim does not catch the front or prevent you from taking shoes out. Keep the cabinet’s intended openings unobstructed, and do not treat it as a shoe dryer.
Verifying Fixings, Fit, and Shoe Condition
The final check is practical: the cabinet stays secure, opens as intended, and holds dry shoes without blocking the passage. A quick inspection after loading can reveal movement or fit problems. Recheck the installation if the cabinet loosens, bends, or becomes hard to open.
Load and inspect with dry shoes
The cabinet is made of polypropylene plastic, but no material-tolerance value or manufacturer-specified airflow figure is established here. Do not infer a safe load limit or assume the cabinet provides enough airflow to dry wet footwear.
Before regular use:
- Put in dry shoes and check that the front opens and closes as intended.
- Look for looseness at the fixings or visible deformation.
- Confirm that shoes do not prevent the cabinet from closing.
- Check the hallway’s narrowest clear width again.
- Air-dry damp shoes before putting them inside.
A tight cabinet can hold moisture around wet shoes, which may lead to odor or mold. Drying footwear first is the safer routine. If the cabinet or its fixings move under normal use, remove the shoes and check the installation before using it again.
Example layouts to test
These are planning scenarios, not tested load ratings or promises that a particular wall will work. They show how the same cabinet dimensions can lead to different decisions depending on the wall, access, and available passage.
- Short entry wall: A pair of cabinets may suit a clear wall section. Measure the full width and check that nearby doors do not strike the fronts.
- Narrow hall: Even one slim cabinet can reduce the clear passage. Measure the finished width and verify the local requirement before choosing the wall.
- Wall with uncertain construction: Delay installation until you know what the wall is made of and can choose suitable mechanical fasteners.
- Damp-weather entry: Use the cabinet for dry shoes, not wet ones. Air-dry damp footwear elsewhere first.
The right layout is the one that fits the wall, allows access, and preserves required circulation. If any of those checks fail, relocate the cabinet rather than forcing the fit.
Conclusion and FAQ
A TRONES cabinet can conceal everyday shoes in a shallow footprint, but safe placement depends on the exact model, wall, and room layout. Measure first, use the required wall fixings, preserve access and hallway clearance, and store only dry footwear. These checks help keep the cabinet useful without turning a small storage project into a safety or repair problem.
How deep is an IKEA TRONES cabinet?
One cabinet is nominally 7⅛ inches deep, 20½ inches wide, and 15⅜ inches high (18 × 52 × 39 cm). Check the product details for your exact model and market before measuring the wall or planning a row.
Does IKEA require TRONES to be attached to the wall?
Yes. Attach the cabinet to the wall as required by its assembly instructions. The correct fixing depends on the wall material, so do not assume one anchor type will work for every installation.
Can I attach TRONES with adhesive?
Do not use adhesive in place of the wall attachment required by IKEA. Use a mechanical fixing method suitable for the actual wall and the product instructions. If you cannot confirm the substrate, get qualified advice before installing.
Can TRONES go in a hallway?
It can go in a hallway only if the cabinet does not obstruct access or reduce clear passage below the applicable local requirement. Where adopted, IRC §R311.6 sets a 36-inch (914 mm) minimum hallway width. Measure the narrowest finished point.
How do I choose anchors for a TRONES cabinet?
First identify the wall material and follow the current assembly instructions. Choose fasteners rated for that substrate and installation. No universal anchor or load rating can be given without knowing the wall and the cabinet’s loading.
Can I store wet shoes in a TRONES cabinet?
Air-dry wet or damp shoes before storing them. Moisture trapped in a tight cabinet can contribute to odor or mold. The cabinet is not specified as ventilated drying equipment, and no airflow rating is established here.
Can I add trim around the cabinets?
You can add nonstructural trim only if it does not block the front, access to the fixings, or the cabinet’s removal. Do not seal the cabinet into a permanent enclosure or use trim to support it.
What should I check after installation?
Open and close the cabinet, remove a shoe, and inspect the fixings for looseness or movement. Check for visible deformation, confirm the passage remains clear, and make sure stored shoes are dry. Stop using it if the cabinet shifts.
(This article was written by one of our staff writers, Robert Kensington. Visit our Meet the Team page.)






