What Is Architectural Window Valance Concealment? (Pelmet Boxes)
Architectural window valance concealment, often called a pelmet box, is a fixed or removable box above a window that hides a curtain track, blind headrail, brackets, or the top of a treatment. A good design looks like part of the room while leaving the window, treatment, airflow, and any service points clear and usable.
A pelmet can make a window look tidy and built-in, but its size and fixing method matter. I have seen simple boxes turn into costly rework when a blind could not tilt, a window handle hit the casing, or a service point ended up sealed behind a finished panel. Measuring first usually costs less than repairing a finished wall.
The aim is not to hide every gap at any cost. It is to conceal the hardware while preserving safe operation, access, and code-required clearances. Local building and electrical rules vary, so treat the checks below as a planning guide, then confirm the rules that apply to your home.
Planning: Intent, Code Basis, and Survey
A pelmet is a fixed or removable architectural box that conceals window-treatment hardware. Start by defining what it must cover and what must remain accessible. Record the window, treatment, wall, and nearby services before choosing its depth or height. Then check local code requirements, especially if the window serves as an emergency escape opening.
What does a pelmet conceal?
A pelmet, also called a valance box, is a casing above a window that hides some or all of a curtain track, blind headrail, brackets, or treatment edge. It may be made from wood, plasterboard, or another finish material, and can be fixed or designed for removal.
The terms “pelmet” and “valance” are sometimes used differently by suppliers. In practical installation, the key question is what the box covers and whether it blocks anything that needs to move or be reached.
Before design, write down the intended purpose:
- Conceal a curtain track, blind headrail, brackets, or the treatment’s top edge.
- Leave enough room for the treatment to travel and operate.
- Preserve access to parts that may need adjustment or service.
- Fit the room’s trim and finish without blocking vents or other openings.
What should you survey before sizing it?
A survey is a set of measurements and checks taken before the box is built. It helps establish the box’s position, size, support, and access needs. Measure the actual installed treatment, not only the window frame, because brackets and moving parts may extend beyond it.
Record:
- The finished wall’s projection to the treatment’s furthest point.
- The full path of curtains, blinds, sash, handles, and operators.
- The wall material and the location of framing or other sound fixing points.
- Nearby wires, pipes, HVAC outlets and returns, detectors, and sprinklers.
- Whether the window is an emergency escape and rescue opening.
Building on this, mark the proposed box outline on the wall or make a full-size template. Check it with the treatment installed. For long-term savings, this simple mock-up can prevent avoidable changes to framing, paint, or finished trim.
Use the locally adopted building and electrical codes. The International Residential Code (IRC), International Building Code (IBC), and National Electrical Code (NEC) may have local amendments or different adopted editions. A pelmet is not automatically a fire-rated or sound-rated assembly. Next step: confirm the window’s use, wall support, and service locations before fixing dimensions.
Access and Clearances: Verified Limits and Design Checks
There is no single standard pelmet depth or universal gap that suits every window. The box must clear the treatment through its full movement and must not reduce a required window opening. Airflow and service access also depend on the room’s layout and equipment, so check each condition in place.
How much clearance does a pelmet need?
Operating clearance is the space that keeps the treatment, hardware, and box from touching during use. No universal code clearance applies to pelmets. Measure the tightest point in the treatment’s full travel, including brackets, handles, and finish layers. Set the gap from that check rather than relying on a typical dimension.
For a dependable fit:
- Install or position the actual track, blind, or curtain hardware.
- Move the treatment through its full range.
- Check the sash, handles, and operators through their full movement.
- Make a mock-up or template and confirm that finishes will not close the gap.
Include any room needed to remove or adjust hardware. If the box needs a removable face or panel for service, plan that opening before the frame is covered.
What code and airflow checks matter?
Where IRC §R310 applies, an emergency escape and rescue opening generally needs at least 5.7 square feet of net clear opening, or 5.0 square feet for qualifying grade-floor openings. The minimum clear width is generally 20 inches and the minimum clear height 24 inches. The bottom of the clear opening is generally no more than 44 inches above the floor. Verify the adopted code, exceptions, and the window’s required clear opening.
A pelmet must not prevent the window from opening as required or reduce the required net clear opening. A box near the window head can still interfere with sash travel or an operator, even if it appears to cover only trim.
Keep supply outlets and return-air grilles unobstructed. There is no generally applicable CFM allowance or fixed pelmet-to-register gap. Follow the HVAC designer’s airflow requirements and the equipment maker’s instructions. Do not assume an arbitrary gap will provide enough airflow.
| Check | What to verify | Design response |
|---|---|---|
| Treatment movement | Track, blind, curtain, brackets, and handles | Size from a full-travel test |
| Emergency opening | Required clear area and operating path | Keep the opening compliant with the pelmet installed |
| HVAC | Nearby supply and return openings | Keep them unobstructed; follow system requirements |
| Maintenance | Drivers, junction boxes, and adjustable hardware | Provide approved access where needed |
Next step: test the proposed outline with the treatment and window in motion, then confirm airflow and service access before building.
Execution: Survey, Framing, and Finish
A sound installation begins with a straight, well-supported box and a verified operating gap. Choose the fixing method for the actual wall substrate and the expected loads. Close the box only after checking movement, airflow, and service access. A neat finish should not depend on drywall alone or hide parts that need routine attention.
How should the box be framed and fixed?
Dead load is the weight of the pelmet and its fixed parts. The fixing must also account for forces from operating the treatment and foreseeable service loads. Do not assign a generic load rating to a box or fastener. Check the anchor maker’s published allowable values and installation conditions for the verified substrate.
A practical sequence is:
- Mark the box outline and confirm its position with a template.
- Locate framing or verify the wall material where each fixing will go.
- Build a straight frame with support suited to the box design.
- Select anchors for the substrate and the actual loads.
- Check alignment and treatment movement before attaching finish panels.
Avoid relying on drywall alone unless the fastening system is specifically rated for the calculated load and the installation matches its instructions. If the wall or load path is uncertain, get advice from a qualified builder or engineer.
How do you finish it without losing access?
Close the box only after you have checked treatment operation, egress, airflow, and any equipment or service points behind it. If routine maintenance would require cutting or damaging the finish, provide a removable face or access panel. Keep electrical splices in approved, accessible boxes.
If you add lighting or powered equipment, use listed equipment and wiring methods permitted by the locally adopted NEC. Confirm that drivers, junction boxes, and controls can be reached before closing the assembly. Do not bury a splice or serviceable driver behind a fixed finish.
Illustrative installation scenarios: In a room with a roller blind, the headrail may fit behind a shallow box, but the brackets and blind’s travel still set the needed clearance. In a room with curtains, the track projection and the gathered fabric can demand a different box depth. These examples show why a standard dimension is not a substitute for a physical test.
Next step: inspect the box while all moving parts operate, and keep any required service access usable after finishing.
Verification: Critical Edge Case and Exclusions
Verification means checking the finished pelmet against the original requirements, not just looking at its face. The most important edge case is an emergency escape window whose sash or opening path is partly blocked. Also confirm that the box leaves vents, electrical access, and serviceable hardware clear.
A final check should cover:
- Window operation and any required net clear opening.
- Treatment movement without contact at the tightest point.
- Clear supply outlets and return-air openings.
- Secure fixings suited to the verified substrate and loads.
- Access to electrical boxes, drivers, controls, and serviceable hardware.
Decorative trim does not justify a reduced emergency opening. If the installed treatment or pelmet affects the required opening, revise the design before relying on the window for escape.
Conclusion and FAQ
A well-planned pelmet hides window hardware without hiding problems. Its dimensions come from the installed treatment, wall, window operation, and nearby services, not from a universal size chart. Measure, mock up, verify the local code, and make service access part of the design.
What is a pelmet box?
It is a fixed or removable box above a window that conceals a curtain track, blind headrail, brackets, or treatment edge.
Is a pelmet the same as a valance?
The terms can overlap. Usage varies by region and supplier, so confirm whether a product is a soft fabric valance or a rigid box that hides hardware.
How deep should a pelmet be?
There is no universal depth. Measure the installed hardware and treatment, then test their full movement with a template or mock-up.
Does a pelmet need a set clearance from a blind?
No universal code clearance applies. Leave enough room to prevent contact through the blind’s full operation, including at brackets and controls.
Can a pelmet go over an emergency escape window?
Only if the window still operates and provides the required clear opening under the locally adopted code. Check the opening with the treatment installed.
Can I fix a pelmet to drywall?
Do not assume drywall alone is adequate. Use a fastening system rated for the calculated load and the actual installation, or fix to verified framing or suitable substrate.
Can a pelmet cover an air vent?
No. Keep supply outlets and return-air openings unobstructed, and follow the HVAC designer’s requirements and equipment instructions.
Can electrical drivers or splices go inside a pelmet?
Use listed equipment and permitted wiring methods. Keep splices in approved, accessible boxes and provide access to drivers and controls.
Is a pelmet fire-rated by default?
No. A standard pelmet is not automatically a rated fire or acoustic assembly. Confirm any required rating with the applicable plans and local code.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)






