What Is Decoy Appliance Stash Geometry? (Diversion Safes)
Decoy appliance stash geometry is the layout of a nonworking, appliance-shaped furniture shell, its hidden insert, and the clear space needed to use it safely. It is not a building-code term or a tested security rating. Keep the cavity inside the shell, use rated hardware, and never alter a working appliance or block building services.
The useful idea is to treat a diversion safe as a small piece of furniture, not as a place to hide storage inside a real appliance. That change makes the design easier to measure, test, and keep separate from electrical, plumbing, and ventilation systems.
I start with three measurements: the shell’s inside dimensions, the insert’s full travel path, and the space needed to open and remove it. Together, these describe the stash geometry. A convincing exterior matters less than a stable, accessible build that does not obstruct a required service area.
Planning the Decoy and Checking the Site
Decoy geometry describes how the outer shell, storage cavity, door or panel, and moving hardware fit together. There is no universal size, shape, or code-approved layout. Plan the item as nonfunctional furniture for ordinary household valuables, and check the site before choosing its dimensions.
First, decide whether the object is furniture or a working appliance. This guide covers only nonfunctional furniture. Do not cut, drill, disable, or store items inside a working appliance, electrical panel, utility enclosure, or required service space.
Then survey the location. Note receptacles, wiring, plumbing, vents, service panels, door swings, and other items that need access. Check local rules and ask the authority having jurisdiction (AHJ), the local office that interprets and enforces building requirements, if the location or proposed work raises a code question.
Measure the shell at its narrowest internal points. Record the opening size, not just the outside size. Also measure the route the insert follows as it opens or comes out. A cavity that fits on paper may still fail if a hinge, frame, or cabinet wall blocks the insert.
Make a full-size cardboard mock-up before building. Set it in the planned location, open it, and remove the mock insert. Confirm that it does not touch building services, block access, or interfere with nearby doors and furniture.
Access, Service Clearances, and Ventilation
Service clearances protect access to equipment; they are not extra storage dimensions. Keep the decoy outside required work areas, and do not use a generic ventilation gap as a substitute for an appliance’s installation instructions. If a working appliance is nearby, preserve its full model-specific airflow path.
Where NEC 110.26 applies, electrical equipment generally needs a working-space width of at least 30 inches (762 mm), or the equipment width if greater. The depth is 36 inches (914 mm) for many common conditions, but it can vary with voltage and energized-part conditions. These are service-access rules, not cavity dimensions. Confirm the requirements that apply to the actual equipment and location.
A decoy shell must not cover an electrical panel, receptacle, shutoff, access door, or other point that needs service. Do not assume that an item is safe to cover because it is rarely used. Required access remains required even when the space seems convenient for storage.
There is no universal CFM value or standard gap for appliance-shaped furniture. For a real appliance, follow its model-specific installation manual. Never cover an intake or exhaust opening or reduce the stated clearance. If the decoy shares a cabinet or area with a working appliance, make sure it does not interrupt that appliance’s ventilation route.
Building the Nonfunctional Shell and Insert
A safe shell keeps the complete storage cavity within the furniture body and does not rely on an appliance’s working parts. Use stable materials and hardware with published load ratings. Keep the design simple enough to inspect, remove, and repair without disturbing a wall, utility chase, or rated building assembly.
Measure the cavity after the shell is built, since panels and supports reduce usable space. For a removable, non-load-bearing insert, a 1/8-inch (3 mm) fit allowance can be a starting point. It is not a code tolerance or a guarantee of a smooth fit. Check the allowance with a physical mock-up, since finish layers, out-of-square corners, and material movement can change the fit.
Keep valuables within the insert’s intended size and weight. Choose hinges, slides, fasteners, and locks with published load ratings. The rating must cover the complete moving assembly, including the insert and its contents. Do not estimate capacity from a hinge’s appearance or the number of screws.
A decoy safe is not a listed safe, a child-resistant storage product, or a substitute for legally required secure storage. If your valuables need a tested level of protection, use a product rated for that purpose. Keep the decoy’s role modest: it is a furniture item with a concealed storage space, not a promise of theft resistance.
Loaded-Operation and Safety Verification
Verification means checking the completed build in the condition it will be used, including its contents. Test the insert, closure, stability, clearances, and surrounding area before storing anything. A smooth unloaded movement does not prove that the hardware will work safely under load.
Use this sequence:
- Open and close the insert several times while empty. Check for binding, scraping, loose fasteners, and pinch points.
- Add the intended contents, staying within the hardware maker’s stated limits. Repeat the movement test.
- Check that the shell does not tip, slide, or rock during normal use.
- Confirm that no part touches wiring, plumbing, vents, service panels, or other building systems.
- Check for heat buildup if the item sits near a heat source. Do not place the decoy where it could trap heat around working equipment.
- Keep product instructions and hardware load information with the project records.
If the object was once an appliance, clearly label it as nonfunctional and do not reconnect it to power or plumbing. Any wiring, receptacle, or powered appliance introduces separate listing, installation, access, and inspection requirements. Refer that work to a qualified electrician and the AHJ.
Worked Examples and Measurement Table
The examples below are planning scenarios, not code dimensions or reports of tested products. They show how to compare a measured shell with its intended use. Measure the actual materials and hardware before building; the numbers are starting points for a mock-up, not universal specifications.
| Scenario | Measured shell or opening | Insert plan | Main check |
|---|---|---|---|
| Small decorative cabinet | 18 × 18 × 24 in. exterior | A shallow removable insert sized to the actual interior | Confirm that the opening and removal path clear the frame |
| Low furniture-style shell | 30 in. wide exterior | A hinged or sliding insert sized for the intended contents | Use hardware rated for the loaded assembly; check tipping |
| Appliance-shaped furniture near a working appliance | Measure both objects and their clearances on site | Keep the decoy cavity entirely inside its own shell | Preserve the working appliance’s manual-specified ventilation and access |
For the first scenario, do not assume that a 12-inch-wide insert will fit just because the cabinet is 18 inches wide outside. The frame, side panels, and hardware reduce usable space. Measure inside the finished shell, then make the insert mock-up with the planned fit allowance.
For a sliding insert, test its full path with a cardboard template before installing slides. For a hinged insert, check the swing arc and the space needed to reach or remove it. The outer shape should not force a tight installation that blocks access to nearby equipment.
Common Design Errors to Avoid
The most common geometry error is treating outside dimensions as storage dimensions. The next is overlooking the motion path: the insert needs room not only to sit in the shell but also to open, slide, or come out. Mock-ups catch both problems before hardware is installed.
Other avoidable errors include:
- Using unrated hinges or slides, or exceeding the published load limit.
- Cutting into an appliance, wall assembly, rated enclosure, or utility chase.
- Covering vents or assuming a generic ventilation gap will be enough.
- Placing the decoy in required electrical working space.
- Calling a diversion safe a substitute for a listed safe or required secure storage.
- Leaving a repurposed appliance appearing to be functional when it is not.
If a site check reveals a conflict with access, ventilation, or building services, move the decoy or change its size. Do not solve a fit problem by covering or altering the system that needs clearance.
Conclusion
Good decoy appliance geometry is a measured fit between a nonfunctional shell, a removable cavity, and the space around it. It is not a code formula or a security rating. Survey first, mock up the insert, use rated hardware, and verify the loaded build without blocking building systems.
The safest next step is to measure the actual site and shell, then test a full-size mock-up. If electrical equipment, ventilation, or code requirements are involved, confirm the applicable rules with a qualified professional or the AHJ.
FAQ
What does decoy appliance stash geometry mean?
It means the dimensions and layout of a furniture-like outer shell, its storage cavity, and the space needed to operate the insert.
Is there a standard size for a diversion safe?
No. There is no universal code size. The shell and cavity depend on the measured furniture, intended contents, hardware, and location.
Can I hide items inside a working appliance?
No. Do not alter, disable, or store items inside a working appliance. Use a separate, nonfunctional furniture shell.
Does the 30-inch electrical clearance apply to a stash cavity?
No. Where NEC 110.26 applies, that measurement is part of electrical equipment’s working space. It is not a storage dimension. Requirements vary by conditions and must be checked for the site.
How much clearance should a removable insert have?
A 1/8-inch (3 mm) allowance may be a project starting point for a removable, non-load-bearing insert. Test it with a mock-up; it is not a code tolerance.
Can I place a decoy next to a working appliance?
Only if it does not block the appliance’s access or ventilation. Follow that appliance’s installation manual and keep its intake and exhaust paths clear.
How do I choose hinges or slides?
Use products with published load ratings. The rating must cover the insert and its contents together; appearance alone does not show capacity.
Is a diversion safe a substitute for a listed safe?
No. It is not a tested security rating, child-resistant product, or replacement for legally required secure storage.
What should I test before using the insert?
Test opening, closing, and removal while empty and loaded. Check for binding, tipping, pinch points, loose fasteners, heat buildup, and interference with building systems.
Do I need approval to build one?
A simple furniture item may not require building work, but rules depend on the location and scope. If work affects wiring, a receptacle, a rated enclosure, or building systems, consult a qualified professional and the AHJ.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)




