What Is Masonry Cable Concealment Channeling? (Chasing Specs)
Masonry cable concealment channeling, often called chasing, is the controlled cutting of a narrow groove in masonry to house a code-compliant raceway and wiring. The chase is sized for the listed system, not a standard width or depth. Safe work starts with a wall survey, utility scanning, code review, and structural approval when needed; inspection and records come before patching.
Your goal is a hidden route that remains safe, inspectable at required points, and repairable if the wiring ever needs attention. A neat groove alone does not make a compliant installation. The wall’s structural role, wiring method, boxes, raceway fill, fire rating, and local rules all shape the design.
What masonry cable channeling means
Masonry cable channeling is a groove cut into brick, block, or concrete so wiring can be routed inside the wall and covered with a suitable repair material. In a compliant installation, the groove is planned around an approved wiring method, often a raceway, rather than treated as permission to bury any cable in masonry.
“Chasing” describes the cutting work; it does not define a wiring method or a standard chase size. The route may connect accessible boxes, cabinets, or equipment, but required electrical connections must remain in approved, accessible boxes. A concealed route should not make a junction box inaccessible behind plaster or masonry.
There is no universal code-prescribed chase width, depth, or ventilation rate for ordinary cable routing. Size the chase to suit the selected raceway, compatible fittings, installation access, and the cover needed for the finished wall. If the route serves equipment that produces heat, assess that equipment and installation separately; do not assume the chase needs a particular airflow rate.
Plan the route before cutting
Planning means confirming the wall type, route, wiring method, and applicable rules before removing masonry. The adopted electrical and building codes, local amendments, raceway instructions, and authority having jurisdiction (AHJ) guide the work. A scan helps locate hazards but does not replace structural review or approval.
Start by identifying whether the wall is load-bearing, reinforced, part of a rated assembly, exposed to moisture, or likely to contain embedded services. Look for the proposed cable type and termination points, too. Confirm the code edition and permit or inspection requirements with the AHJ before cutting.
Scan the route for wiring, plumbing, reinforcement, and other embedded items. Scanning has limits, so treat uncertain results with caution. Do not cut reinforced or load-bearing masonry without structural review and approval. Electrical-code compliance does not authorize a structural alteration, and a shallow-looking chase can still damage reinforcement or weaken a wall.
Then choose a wiring method permitted for that location. Do not assume a cable may be buried directly in a masonry chase. Where a listed raceway is needed, select it and its fittings as a compatible system, then use the manufacturer’s installation instructions and the adopted code.
Choose raceway, boxes, and clearances
Raceway sizing is based on the conductors, raceway type, fittings, and route, not on the desired groove dimensions alone. Calculate fill under the adopted code and check box capacity, bend limits, support, and access. These checks determine the space needed before cutting begins.
NEC Chapter 9, Table 1 sets general raceway-fill limits of 53% for one conductor, 31% for two conductors, and 40% for more than two conductors, subject to applicable exceptions. Use the actual internal dimensions for the selected raceway and the dimensions of the conductors. Do not overfill conduit.
For EMT, NEC 358.30 generally requires secure support within 3 ft (900 mm) of each box, cabinet, or conduit body and at intervals no greater than 10 ft (3 m). Check the adopted code text and exceptions. A concealed chase does not remove support requirements; plan how the raceway will be secured as required.
Box fill matters as much as conduit fill. Under NEC 314.16(B)(1), the volume allowances are 2.00 cubic inches per #14 AWG conductor, 2.25 cubic inches per #12 AWG conductor, and 2.50 cubic inches per #10 AWG conductor. The full calculation must also account for items such as equipment grounds, devices, and internal clamps under the adopted rules. Do not choose a box by face size alone.
The 1¼ in (32 mm) protection rule in NEC 300.4(A)(1) generally concerns cables or raceways near the edge of bored holes in wood framing. It is not a required masonry chase cover or depth. Do not transfer a framing dimension to masonry work.
| Design check | What to verify | Why it affects the chase |
|---|---|---|
| Raceway fill | Conductor count, type, and actual raceway dimensions | Determines raceway size |
| EMT support | Generally within 3 ft of boxes and every 10 ft maximum | Affects installation and support plan |
| Box fill | Conductors, grounds, devices, and clamps | Determines box volume |
| Wall condition | Structure, reinforcement, moisture, and rating | Determines whether cutting is suitable |
| Finish cover | Raceway, fittings, and repair material | Determines required groove size |
Cut, install, inspect, and close
The work sequence is survey, mark, cut, install, inspect, test, and patch. Keep the route within approved limits, fit compatible components, and complete any required checks before concealment. Cutting first and resolving code or structural questions later can create expensive repair work and unsafe conditions.
Approve the route. Confirm the wall construction, code edition, permits, inspection needs, wiring method, and route. Get structural review before altering load-bearing or reinforced masonry. Confirm rated-assembly requirements if the wall is fire-resistance rated.
Mark and size. Lay out the path and box locations. Use the raceway and fitting dimensions, fill calculation, bend limits, and installation access to set the chase dimensions. Avoid embedded services and reinforcement. Allow for the approved finish cover; do not invent a standard chase depth.
Cut and install. Cut only the approved route, using methods and dust controls suitable for the material and site. Install the raceway, fittings, boxes, and supports according to the product instructions and code. Maintain required separation between communications and power wiring under applicable rules.
Inspect and test before patching. Pull conductors only after the raceway inspection where required. Verify conductor identification, raceway fill, box fill, bonding and grounding, support, and required electrical tests. Arrange inspections as required by the AHJ.
Firestop and restore. Where a route penetrates a rated assembly, use a firestop system listed for the actual wall, opening, penetrant, and required rating. Systems may be tested to UL 1479 or ASTM E814 where required by the adopted code. Generic sealant is not a substitute. Photograph the open route and record its location before patching with compatible materials.
Typical installation scenarios
These examples are planning scenarios, not reports of specific completed projects. They show how wall conditions change the decision. I treat the wall survey as the first design step, because a route that fits the electrical plan may still be unsuitable for the structure or rated assembly.
| Scenario | Main concern | Practical next step |
|---|---|---|
| Non-structural masonry partition | Raceways, boxes, finish cover, and access | Confirm the wall is non-structural, then size the route to the selected system |
| Reinforced or load-bearing wall | Reinforcement and structural capacity | Stop before cutting and obtain structural review |
| Rated masonry wall | Maintaining the tested fire-resistance assembly | Confirm the listed firestop detail for the exact penetrant and wall |
| Damp or exposed area | Wiring-method suitability for the environment | Confirm the raceway, fittings, and conductors are permitted for the location |
A common planning mistake is to choose a groove width from a familiar cable size, then find that the raceway, fitting, or bend will not fit. Work from the full listed installation instead. Another is to patch before inspection, testing, and firestopping are complete. Keep the route open until required approvals and checks are done.
Common questions about masonry chases
These answers summarize the main decisions involved in chasing a masonry wall for wiring. Local code adoption and amendments matter, so use them as a planning guide, then confirm the installation details with the AHJ and qualified trade professionals where required.
Is there a standard chase width or depth?
No. Size it for the listed raceway, fittings, installation access, and required finish cover. There is no universal code-prescribed dimension for an ordinary cable chase.
Can I bury cable directly in a masonry groove?
Do not assume so. Confirm that the cable wiring method is permitted for that location and installation. Use a code-compliant, listed raceway where required.
Can I chase a load-bearing or reinforced masonry wall?
Not without structural review and approval. Cutting can damage reinforcement or reduce wall capacity, even if the groove seems shallow.
What raceway fill limits should I use?
NEC Chapter 9, Table 1 generally gives 53% for one conductor, 31% for two, and 40% for more than two, subject to exceptions. Apply the adopted code and actual component dimensions.
How often must EMT be supported?
NEC 358.30 generally requires support within 3 ft of boxes, cabinets, or conduit bodies and at intervals no greater than 10 ft. Verify the adopted text and applicable exceptions.
How do I calculate box fill?
Use the adopted NEC 314.16 rules. The volume allowances include 2.00 cubic inches per #14 AWG conductor, 2.25 per #12 AWG, and 2.50 per #10 AWG, with the full calculation including other applicable items.
Does the 1¼-inch rule set masonry cover depth?
No. NEC 300.4(A)(1) generally addresses protection near bored holes in wood framing. It is not a masonry chase-depth rule.
How should a rated wall penetration be sealed?
Use a firestop system listed for the actual wall, opening, penetrant, and required rating. A generic sealant does not establish that the wall’s rating has been restored.
Should I pull wires before the raceway is inspected?
Follow the required inspection sequence. Where a raceway inspection is required, keep it open and have it inspected before pulling conductors.
Can the chase be patched as soon as the raceway is installed?
Not if required inspection, testing, or firestopping remains incomplete. Verify the installation, document the route, and obtain required approvals before closing it.
A sound masonry cable chase is sized from the wiring system and checked against the wall’s structure and rating. Survey first, get the right approvals, and keep the route accessible until required inspections and tests are complete. That process supports a concealed finish without trading away electrical or structural safety.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)






