What Is Vertical Concealed Cabinetry? (Concealed Hinges)
Vertical concealed cabinetry is a cabinet with a door that swings on a vertical edge while its hinges stay hidden when the door is closed. Most often, the hinges are adjustable cup hinges fitted into the door and cabinet side. Correct design depends on the door’s size and weight, hinge instructions, sound cabinet attachment, clear swing space, and unobstructed building services.
What vertical concealed cabinetry means
Vertical concealed cabinetry has a door that rotates around a vertical side edge, like a standard cabinet door, while concealing its hinge hardware from normal view when closed. The term describes the door’s swing and hinge appearance; it does not define a special cabinet type or a guaranteed concealment rating.
In common residential use, the door is attached with European-style concealed hinges. A round cup sits in a bore on the back of the door, and an arm connects it to a mounting plate on the cabinet. The closed door covers the hinge, though the hinge may be visible when the door is open.
This differs from a pocket door, which slides into a wall or cabinet, and a lift-up door, which swings or rises on a horizontal axis. “Vertical” refers to the axis of rotation, not the direction the door travels.
A well-planned cabinet can also feel easier to use. For example, placing everyday items within a comfortable reach may reduce repeated bending or reaching. That is a layout benefit, not a health claim, and it does not change the cabinet’s structural or code obligations.
Planning the cabinet, door, and concealed-hinge system
Start by measuring the opening, proposed door, cabinet panels, and nearby obstructions. Then select a hinge for the actual door dimensions and mass. Cabinet and hinge instructions guide the layout; ANSI/BHMA A156.9 applies to cabinet hardware where specified, but it does not set one universal hinge count or reveal for every installation.
Before ordering or drilling, record:
- Opening width and height, measured at more than one point
- Door width, height, thickness, and estimated finished weight
- Cabinet-side material and thickness, plus how the cabinet will attach to the building
- Hinge overlay, opening angle, cup depth, and screw requirements
- Nearby walls, trim, handles, lights, outlets, pipes, ducts, and equipment
Overlay is how far the door covers the cabinet edge. Hinge type and mounting position determine overlay, so do not assume that hinges with similar names fit the same layout. A full-overlay hinge, for example, is meant for a different door position than an inset hinge.
A 35 mm cup bore is common for European concealed hinges, but it is not universal. Cup depth is often about 12–13 mm for this style. Check the exact hinge data sheet and drilling template before boring. The remaining wood between the cup and the door’s front face must be sufficient for the door material and maker’s instructions.
Include the handle and finish when estimating door mass. If you do not have a reliable weight figure, weigh the completed door or calculate it from the material data. Then use the hinge maker’s table for door height, width, thickness, and weight. There is no safe general rule for weight per hinge.
Checking swing paths, reveals, and service clearances
A swing-path check confirms that the door can open through its intended angle without hitting a wall, handle, trim, appliance, or person’s route. A service-clearance check confirms that the cabinet does not cover openings or block access required for building systems or equipment.
Make a full-size door outline from cardboard or a thin panel and test the planned swing. Check both the door edge and the handle, which may extend beyond it. A hinge’s stated opening angle is not proof that the installed door will clear nearby objects.
Keep required access and airflow in view. An ordinary cabinet has no general CFM airflow requirement, but it must not cover required HVAC grilles, combustion-air openings, or appliance ventilation. Preserve equipment listing instructions and installation clearances. Do not block shutoffs or electrical equipment that need access.
For fit, a 2 mm reveal, or gap between door and cabinet, is a practical shop target for many doors, not a code minimum. The hinge maker’s overlay and adjustment geometry take priority. As a workmanship target, aim for door edges within 1.5 mm over 2 m; this is not a code tolerance.
| Check | Practical method | What to verify |
|---|---|---|
| Door swing | Mock up the door outline | Full opening without collision |
| Reveal | Measure gaps at several points | Even appearance and free movement |
| Cup bore | Use the selected hinge template | Correct diameter, depth, and edge distance |
| Service access | Compare with equipment instructions | No blocked vent, clearance, or required access |
Installing the cabinet, hinge cups, and door
Install the cabinet square and plumb before hanging the door. A twisted or out-of-square cabinet can make a correctly drilled door bind or show uneven gaps. Confirm that the cabinet is attached to framing or another suitable support for its weight and use; hinge screws should not be asked to hold a weak cabinet side in place.
A sound sequence is:
- Mark the layout. Follow the hinge maker’s measurements for cup position, edge distance, and mounting plate location. Make a test bore in scrap of the same thickness when possible.
- Bore the cups. Use the specified bit and depth stop. Keep the drill square to the door face, and stop at the listed depth. A deep bore can break through the front face or weaken the door.
- Fasten the hinges. Use the specified screws and hole pattern. Avoid overdriving screws, which can damage the panel or reduce their hold.
- Attach mounting plates. Keep plate positions consistent and use the maker’s specified fasteners. Confirm that the cabinet material can support the connection.
- Hang and adjust the door. Support the door while fastening it. Use the hinge adjustments to set side-to-side position, height, and depth, as provided by that hinge model.
- Test under use. Open and close the door several times. Check for binding, screw movement, contact at the frame, and changes in reveal.
Do not fill gaps or add trim in a way that traps the hinge arm. If the door needs a wider opening angle, select hardware designed for it and confirm that the cabinet layout allows that motion.
Verifying alignment, load support, and unobstructed ventilation
A final check tests the whole assembly, not just the door’s appearance. Inspect cabinet attachment, hinge fasteners, reveals, swing clearance, and any nearby vents or service points. Recheck after the door carries its normal handle and finish, since added mass and use can expose a weak mounting point.
I use a simple acceptance checklist for a typical cabinet installation:
- Cabinet is square, plumb, and firmly attached.
- Hinge model and quantity match the manufacturer’s door-size and load guidance.
- Door opens and closes without rubbing or striking adjacent surfaces.
- Reveals are consistent with the chosen overlay and hinge adjustment range.
- No required grille, combustion-air opening, equipment clearance, shutoff, or electrical access is blocked.
- Finish and trim do not bind the hinge or stop the door from closing.
The hinge maker’s load guidance is the deciding source for hinge selection. Do not substitute a generic “weight per hinge” estimate. If the door is unusually large, heavy, or made from a material not covered by the hinge table, ask the hinge supplier or cabinet maker for a suitable model and layout.
Installation examples: two common situations
These examples show how the same hinge principles apply to different cabinet layouts. They are planning scenarios, not reported job records or claims of tested performance. In each case, confirm dimensions and hardware against the selected manufacturer’s instructions.
Inset door in a hallway cabinet: An inset door sits inside the cabinet opening, so the opening dimensions, door size, and reveal must be coordinated. A 2 mm gap can be a useful shop target, but the hinge’s adjustment range and the cabinet’s actual squareness govern the final fit. A handle or nearby wall can limit the swing, so test the door outline before drilling.
Full-overlay door near an appliance: A full-overlay door covers more of the cabinet front. The installer must select a hinge designed for that overlay and check the appliance instructions before setting the cabinet position. If the cabinet is near a vent or service panel, the door must not cover required ventilation or prevent access. The appliance’s listing and instructions take priority over a preferred cabinet layout.
In both cases, the useful lesson is the same: choose the hinge from the actual door and cabinet geometry, then verify the opening in place.
Common questions about concealed cabinet hinges
These answers cover the basic terms, typical measurements, and installation limits for vertically swinging cabinet doors. Exact dimensions and hardware choices depend on the selected hinge, door material, cabinet construction, and equipment nearby.
What is a concealed cabinet hinge?
It is a hinge fitted into the door and cabinet so the hardware is hidden from normal view when the door is closed. European cup hinges are a common type.
What does vertical mean in vertical concealed cabinetry?
It describes a door that rotates around a vertical side edge. It does not mean the door lifts upward or slides into a wall.
Are all concealed hinges drilled with a 35 mm bit?
No. A 35 mm cup is common, but not universal. Use the drilling template and bore size specified for the exact hinge.
How deep should a concealed-hinge cup bore be?
Many 35 mm-cup hinges use a cup depth near 12–13 mm. Confirm the exact depth in the hinge instructions and leave enough material at the door face.
What reveal should I use around a cabinet door?
A 2 mm reveal is a practical target for many shop-built doors, not a code rule. Follow the hinge’s overlay and adjustment details, and account for the cabinet’s actual dimensions.
How many hinges does a cabinet door need?
There is no universal count. Choose the hinge model and quantity using the manufacturer’s tables for door height, width, thickness, and finished weight.
Do concealed hinges have a standard weight rating?
No single rating applies to all hinges. Check the selected model’s data and include the handle and finish in the door weight.
Can a cabinet door cover an HVAC grille or appliance vent?
No, not if doing so blocks required airflow or violates equipment instructions. Preserve applicable clearances, ventilation, and access requirements.
Can concealed cabinet hinges be used on a fire-rated door or wall opening?
Ordinary cabinet hinges do not create a fire-rated assembly. Do not use a cabinet front as a substitute for a required fire door or compromise a rated partition; check listed-system documents and the local code official.
What should I check before drilling the door?
Confirm the door thickness, cup position and depth, hinge overlay, mounting-plate location, screw requirements, and swing clearance. A test bore in matching scrap helps check the setup before cutting the finished door.
(This article was written by one of our staff writers, Garrett Vance. Visit our Meet the Team page.)






